參數資料
型號: MF0512M-11ATxx
廠商: Mitsubishi Electric Corporation
英文描述: ER 22C 18#16 4#12 PIN RECP
中文描述: 16位產品數據總線閃存阿拉木圖PC卡
文件頁數: 5/32頁
文件大?。?/td> 584K
代理商: MF0512M-11ATXX
MITSUBISHI STORAGE CARD
Preliminary
MF0XXXX-11ATXX series
ATA PC CARDS
MITSUBISHI
ELECTRIC
5
June.2001 Rev. 1.3
Signal Description(Continued)
Signal Name
Attribute Memory Select[REG#]
(PC Card Memory Mode)
Attribute Memory Select[REG#]
(PC Card I/O Mode)
Attribute Memory Select[REG#]
(IDE ATA Interface)
Battery Voltage Detect[BVD2]
(PC Card Memory Mode)
Audio Digital Waveform[SPKR#]
(PC Card I/O Mode)
DASP#
(IDE ATA Interface)
Card Reset[RESET]
(PC Card Memory Mode)
Card Reset[RESET]
(PC Card I/O Mode)
Card Reset[RESET#]
(IDE ATA Interface)
Wait[WAIT#]
(PC card Memory Mode)
Wait[WAIT#]
(PC card I/O Mode)
IORDY
(IDE ATA Interface)
Input Port Acknowledge[INPACK#]
(PC Card I/O Mode)
Input Port Acknowledge[INPACK#]
(IDE ATA Interface)
Battery Voltage Detect[BVD1]
(PC Card Memory Mode)
STSCHG#
(PC Card I/O Mode)
I/O
I
Pin No.
Description
When this signal is asserted, access is limited to
Attribute Memory with OE#/WE# and I/O Space
with
IORD#/IOWR#.
This input signal is not used for this mode and
should be connected to Vcc by the host.
This output is driven to a high-level.
61
O
SPKR# is kept negated because this Card does not
have digital audio output.
This signal is the DISK Active/Slave Present signal
in the Master/Slave handshake protocol.
By assertion of this signal, all registers of this Card
are cleared. This signal should be kept to High-Z or
High Level by the host for at least 1ms after Vcc
applied.
This input pin is the active low hardware reset from
the host.
This signal is asserted to delay completion of the
memory or I/O access cycle.
I/O
62
I
58
O
59
O
60
This signal is asserted when the Card is selected
and can respond to an I/O Read cycle at the
address on the address bus.
This output is driven to a high-level.
O
This signal is asserted low to alert the host to
changes in the status of Configuration Status
Register in the Attribute Memory Space.
This signal is the Pass Diagnostic signal in the
Master/Slave handshake protocol.
VS1 is grounded so that the Card CIS can be read
at 3.3V and VS2 is N.C.
This signal is not used for this mode.
PDIAG#
(IDE ATA Interface)
Voltage Sense[VS1, VS2]
Cable Select[CSEL]
(PC card Memory Mode)
Cable Select[CSEL]
(PC card I/O Mode)
Cable Select[CSEL]
(IDE ATA Interface)
I/O
63
O
43, 57
-
-
I
56
This signal is used to configure this Card as a
Master or a Slave. When this signal is grounded,
this Card is configured as a Master. When this
signal is Open, this Card is configure as a Slave.
5V or 3.3V power.
Ground.
Vcc
GND
-
-
17, 51
1, 34, 35, 68
相關PDF資料
PDF描述
MF0128M-07ATxx 8/16-bit Data Bus Flash ATA PC Card
MF0512M-07ATxx Circular Connector; No. of Contacts:22; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:28; Circular Contact Gender:Socket; Circular Shell Style:Box Mount Receptacle RoHS Compliant: No
MF0640M-07AFxx RESISTOR: 75.0K, 1/10W, 1%, PACKAGE 0805
MF0640M-07BFxx 8/16-bit Data Bus Flash ATA PC Card
MF0512M-07BTxx Triaxial Cable; Coaxial RG/U Type:59; Impedance:75ohm; Conductor Size AWG:20; No. Strands x Strand Size:Solid; Jacket Material:Foam HDPE; Leaded Process Compatible:Yes RoHS Compliant: Yes
相關代理商/技術參數
參數描述
MF05A 制造商:NSC 制造商全稱:National Semiconductor 功能描述:MOLDED SOT-23 115 X 063 X 040 IN BODY 5LD 0375 IN PITCH
MF0601 制造商:KYUNG NAM ELECTRONICS 功能描述:T1, VACUUM LAMP,28V,24MA
MF0603 制造商:KYUNG NAM ELECTRONICS 功能描述:T1 LAMP,48V 25MA
MF060R/R 制造商:Brady Corporation 功能描述:SIGN FIRE EXIT KEEP CLEAR 200X200MM
MF060R/S 制造商:Brady Corporation 功能描述:SIGN FIRE ESCAPE KEEP CLEAR 200X200