- 您現在的位置：買賣IC網 > PDF目錄359163 > MGA-82563-TR1 0.1-6 GHz 3V, 17 dBm Amplifier PDF資料下載
參數資料
| 型號： | MGA-82563-TR1 |
| 英文描述： | 0.1-6 GHz 3V, 17 dBm Amplifier |
| 中文描述： | 0.1-6 GHz的3V的，17 dBm的放大器 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 137K |
| 代理商： | MGA-82563-TR1 |
6-213
To assist designers in optimizing
not only the immediate circuit
using the MGA-82563, but to also
optimize and evaluate trade-offs
that affect a complete wireless
system, the
standard
deviation
(
σ
) is provided for
many of the Electrical Specifica-
tions parameters (at 25
°
) in
addition to the mean. The stan-
dard deviation is a measure of the
variability about the mean. It will
be recalled that a normal distribu-
tion is completely described by
the mean and standard deviation.
Standard statistics tables or
calculations provide the probabil-
ity of a parameter falling between
any two values, usually symmetri-
cally located about the mean.
Referring to Figure 12 for ex-
ample, the probability of a param-
eter being between
±
1
σ
is 68.3%;
between
±
2
σ
is 95.4%; and be-
tween
±
3
σ
is 99.7%.
68%
95%
99%
Parameter Value
Mean (
μ
)
(typical)
-3
σ
-2
σ
-1
σ
+1
σ
+2
σ
+3
σ
Figure 12. Normal Distribution.
RF Layout
The RF layout in Figure 13 is
suggested as a starting point for
microstripline designs using the
MGA-82563 amplifier. Adequate
grounding is needed to obtain
optimum performance and to
maintain stability. All of the
ground pins of the MMIC should
be connected to the RF
groundplane on the backside of
the PCB by means of plated
through holes (vias) that are
placed near the package termi-
nals. As a minimum, one via
should be located next to each
ground pin to ensure good RF
grounding. It is a good practice to
use multiple vias to further
minimize ground path inductance.
8
50
50
RF Input
RF Output
and V
d
Figure 13. RF Layout.
In addition to the RF consider-
ations, the use of multiple vias for
grounding is important for the
purpose of providing a lower
resistance thermal path to the
heatsink.
It is recommended that the PCB
pads for the ground pins
not
be
connected together underneath
the body of the package. PCB
traces hidden under the package
cannot be adequately inspected
for SMT solder quality.
PCB Material
FR-4 or G-10 printed circuit board
materials are a good choice for
most low cost wireless applica-
tions. Typical board thickness is
0.020 to 0.031 inches. The width of
the 50
microstriplines on PC
boards in this thickness range is
also very convenient for mounting
chip components such as the
series inductor at the input or DC
blocking and bypass capacitors.
For higher frequencies or for
noise figure critical applications,
the additional cost of PTFE/glass
dielectric materials may be
warranted to minimize transmis-
sion line loss at the amplifier’s
input. A 0.5 inch length of 50
microstripline on FR-4, for
example, has approximately
0.3dB loss at 4 GHz. This loss will
add directly to the noise figure of
the MGA-82563.
Biasing
The MGA-82563 is a voltage-
biased device and is designed to
operate from a single, +3 volt
power supply with a typical
current drain of 84 mA. The
internal current regulation circuit
allows the amplifier to be oper-
ated with voltages as low as
+1.5volts. Refer to the section
titled “Operation at Bias Voltages
Other than 3 Volts” for informa-
tion on performance and precau-
tions when using other voltages.
Typical Application
Example
The printed circuit layout in
Figure 14 can serve as a design
guide. This layout is a
microstripline design (solid
groundplane on the backside of
the circuit board) with a 50
input and output. The circuit is
fabricated on 0.031-inch thick
FR-4 dielectric material. Plated
through holes (vias) are used to
bring the ground to the top side of
the circuit where needed. Multiple
vias are used to reduce the
inductance of the paths to ground.
IN
OUT
+V
H
MGA-8-A
Figure 14. PCB Layout.
相關PDF資料 |
PDF描述 |
|---|---|
| MGB2310TK-X | 128 x 64 pixel format, LED or EL Backlight available |
| MGB27TA-X | ULTRA HIGH BRIGHTNESS GREEN LED LAMP |
| MGB31TA-X | ULTRA HIGH BRIGHTNESS GREEN LED LAMP |
| MGB31TAH | ULTRA HIGH BRIGHTNESS GREEN LED LAMP |
| MGB34T-1 | LED 2HI 5MM RED/GRN BICLR PC MNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MGA82563TR1G | 制造商:Avago Technologies 功能描述: |
| MGA-82563-TR1G | 功能描述:射頻放大器 3 SV 13.2 dB RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MGA-82563-TR2G | 功能描述:射頻放大器 3 SV 13.2 dB RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MGA83563 | 制造商:HP 制造商全稱:Agilent(Hewlett-Packard) 功能描述:+22 dBm PSAT 3V Power Amplifier for 0.5-6 GHz Applications |
| MGA83563BLK | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:+22 dBm PSAT 3V Power Amplifier for 0.5? 6 GHz Applications |
發布緊急采購，3分鐘左右您將得到回復。