- 您現在的位置：買賣IC網 > PDF目錄383601 > MH88520-1 (Mitel Networks Corporation) German Subscriber Line Interface Circuit (SLIC) Preliminary Information PDF資料下載
參數資料
| 型號： | MH88520-1 |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | German Subscriber Line Interface Circuit (SLIC) Preliminary Information |
| 中文描述： | 德國用戶線接口電路（SLIC）的初步信息 |
| 文件頁數： | 3/10頁 |
| 文件大?。?/td> | 105K |
| 代理商： | MH88520-1 |
2-65
Preliminary Information
MH88520-1
Functional Description
The BORSH Functions
The MH88520-1 performs all of the Borsh functions
of Battery Feed Overvoltage Protection, Ringing,
Supervision and Hybrid (2-2 Wire).
Return Loss at Tip-Ring
To maximise return loss, the impedance at Tip-Ring
should match the SLIC’s impedance (220R + 820R //
115nF). However, the SLIC’s input impedance is
dependent on the JUNCTOR termination resistance.
Therefore the JUNCTOR must be terminated with
754
.
Figure 3 illustrates a typical connection between two
SLICs through two crosspoint switches. Optimum
return loss occurs when the JUNCTOR is terminated
with 754
. Since the JUNCTOR input/output
impedances is 604
and the crosspoint switch
resistances are 75
+ 75
, this configuration gives
optimum return loss as shown in Figure 4.
Hybrid
The 2-2 wire hybrid circuit converts the incoming
balanced signal at Tip and Ring of the telephone line
into a ground referenced output signal at JUNC of
the SLIC, and converts the ground referenced input
signal at JUNC of the SLIC into the non-balanced
output signal at Tip-Ring of the telephone line.
Mute
A logic low at the MUTE input results in muted
signals coming from Tip and Ring to the JUNC
terminal while allowing signals from the JUNC
terminal to Tip and Ring to be transmitted.
Overvoltage Protection
The MH88520-1 is protected from short term (1ms)
(+250V) between Tip and Ring, Tip and Ground, and
Ring and Ground. However, additional protection
circuitry may be needed depending upon the
requirements which must be met for the final
equipment.
Loop Detection
The loop detection circuit determines whether a low
enough path is across Tip and Ring to be recognised
as an off-hook condition. (Threshold impedance =
5.4k
with no adjustment). This threshold level can
be adjusted by the use of external resistors as
shown in Figure 6. When an off-hook condition
occurs the SHK and LED outputs toggle to a logic
low level. These outputs also toggle during incoming
dial pulses.
Figure 3 - SLIC Crosspoint Switch Connection
MH88520-1
TIP
MH88520-1
TIP
RING
TIP
RING
RING
TIP
RING
JUNC
JUNC
75
75
CROSSPOINT
SWITCH
SWITCH
CROSSPOINT
16
16
1
3
1
8
SLIC 1
SLIC 2
相關PDF資料 |
PDF描述 |
|---|---|
| MH88524 | Dual 2-4 Wire Circuit(雙2-4線電路（在4線設備和話音開關之間提供兩個接口）) |
| MH88524 | Dual 2-4 Wire Circuit Preliminary Information |
| MH88600 | Global SLIC Preliminary Information |
| MH88610 | Subscriber Line Interface Circuit (SLIC) Preliminary Information |
| MH88612BV-K | Subscriber Line Interface Circuit (SLIC)(混合用戶線接口電路（SLIC）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MH88524 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Dual 2-4 Wire Circuit Preliminary Information |
| MH88600 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Global SLIC Preliminary Information |
| MH88610 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Line Interface Circuit (SLIC) Preliminary Information |
| MH88612 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Line Interface Circuit (SLIC) Preliminary Information |
| MH88612B | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Subscriber Line Interface Circuit (SLIC) |
發(fā)布緊急采購，3分鐘左右您將得到回復。