參數資料
型號： MIC2569YQS TR
廠商： Micrel Inc
文件頁數： 13/15頁
文件大?。?/td> 715K
描述： IC POWER SWITCH CABLECARD 16QSOP
標準包裝： 2,500
類型： 熱交換控制器
應用： 衛星/線纜/DVR/電視機頂盒，視頻記錄器，游戲控制臺
內部開關： 是
電流限制： 2.3A
電源電壓： 3.3V，5V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 16-QSOP
包裝： 帶卷 (TR)
Micrel, Inc.
MIC2569
 
 
September 2007 
13
M9999-092507-C
 (408) 944-0800
 
Application Information
CableCARD" Operating Modes
The OpenCable system has a host component (S-Host
or M-Host) and a card component (S-Card or M-Card).
The   host   /   card   combination   determines   which
operational mode is used i.e. S-Mode or M-Mode. This
in turn determines the appropriate state diagram. Table
3 below shows all of the combinations and operating
modes.
 
S-Host
M-Host
S-Card
S-Mode
S-Mode or No power
M-Card
S-Mode
M-Mode
 
Table 3 Operating Mode Combinations
 
An M-Host has the choice to accept or not accept an S-
Card. If the M-Host accepts the S-Card then the M-Host
will   initiate   a   change   from   M-Mode   to   S-Mode.
Otherwise, the M-Host will not power-up the S-Card.
S-Host
After power-up, the S-Host remains in state 0 [000]
unless one of two events occurs:
1.   CIS Request  The CableCard" may request
that the Vpp outputs be provided with 5VIN, that
is, enter state 1 [001]. It is the S-Host decision
whether to provide the Vpp outputs with 5VIN.
The S-Host has two possible options.
a.   If the S-Host refuses to provide 5VIN,
then the S-Host does not change to
state 1 [001] and will remain in state
0 [000], even upon card removal. See
paragraph 2 below.
b.   If the S-Host grants 5VIN, then S-Host
changes to state 1 [001]. The S-Host
remains   in   state   1   [001]   without
returning. See paragraph 2 below.
2.   Card removal  Upon card removal, the S-Host
has two possible options:
a.   The S-Host changes directly to state
0 [000], regardless of the state at card
was removed.
b.   The S-Host has the option to pass
through state 6 [110] to remove any
excessive voltage or charge on the Vpp
outputs. The S-Host then returns to
state 0 [000].
Figure 1 shows S-Mode power state diagram.
 
 
Figure 1 S-Host Power State Diagram
M-Host
1.   Power-up - Upon power-up, M-Host two options:
a.   Move directly the state 2 [010]
b.   Pass through state 7 [111] to remove any
excess voltage or charge, then move to
state 2 [010]
2.   No Card  M-Host will remain in state 2 [010]
until card insertion.
3.   Card Detection  If the M-Host detects that the
inserted card is an M-card, then the M- Host will
change to state 3 [011]. This informs the card
that the host is an M-Host.
4.   Card   ID      The   M-Host   uses   the   card
identification process to determine what type of
card it is and what modes the card can operate
in. There are three options:
a.   If the card is an M-Card, then the M-
Host will change to state 4 [100] and
remain   in   state   4   [100]   until   card
removal.
b.   If the card is an S-Card able to support
CH1, then the M-Host will reset the card
and power-up in S-Mode. The card will
remain in S-Mode until card removal.
c.   If the card is not an M-Card, or an S-
Card not able to support Ch1, then
power will not be provided to the card.
The card will remain without power and
not change state until card removal.
相關PDF資料
PDF描述
MIC2583R-MBQS TR IC CTRLR HOT SWAP 200MV 16-QSOP
MIC2585-2MBTS TR IC CTRLR HOT SWAP DUAL 24-TSSOP
MIC2586R-2BM TR IC CTRLR/SEQ HOT SWAP 14-SOIC
MIC2587R-2BM TR IC CTRLR HOT SWAP POS HV 8-SOIC
MIC2590B-5BTQ TR IC PCI HOT PLUG CTLR DUAL 48TQFP
相關代理商/技術參數
參數描述
MIC2570-1BM 功能描述:IC REG BOOST 2.85V/3.3V/5V 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12
MIC2570-1BM TR 功能描述:IC REG BOOST 2.85V/3.3V/5V 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12
MIC2570-1YM 功能描述:直流/直流開關調節器 Two Cell Boost Regulator (Lead Free) RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MIC2570-1YM TR 功能描述:直流/直流開關調節器 Two Cell Boost Regulator (Lead Free) RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MIC2570-2BM 功能描述:IC REG BOOST ADJ 1A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*