- 您現在的位置：買賣IC網 > PDF目錄377966 > MIC2593-2BTQ (意法半導體) Dual-Slot PCI Hot Plug Controller PDF資料下載
參數資料
| 型號： | MIC2593-2BTQ |
| 廠商： | 意法半導體 |
| 英文描述： | Dual-Slot PCI Hot Plug Controller |
| 中文描述： | 雙插槽的PCI熱插拔控制器 |
| 文件頁數： | 19/26頁 |
| 文件大?。?/td> | 170K |
| 代理商： | MIC2593-2BTQ |
April 2004
19
M9999-042204
MIC2593
Micrel
Status Register Slot B (STATB)
8-Bits, Read-Only
Status Register, Slot B (STATB)
D[5]
D[4]
read-only
read/write
VAUXB
VAUXBF
D[7]
D[6]
D[3]
D[2]
D[1]
D[0]
read-only
FAULTB
read-only
MAINB
read/write
12MVBF
read/write
12VBF
read/write
5VBF
read/write
3VBF
Bit(s)
FAULTB
Function
Operation
FAULT Pin Status
–
Slot B
1 = /FAULTB pin asserted
(/FAULTB pin is LOW)
0 = /FAULTB pin de-asserted
(/FAULTB pin is HIGH)
See Notes 1 and 2
Represents the actual state (on/off) of the
four Main Power outputs for Slot B
(+12V,
–
12V, +5V and +3.3V)
1 = MAIN Power ON
0 = MAIN Power OFF
Represents the actual state (on/off) of the
Auxiliary Power output for Slot B
1 = AUX Power ON
0 = AUX Power OFF
1 = Fault 0 = No fault
1 = Fault 0 = No fault
1 = Fault 0 = No fault
1 = Fault 0 = No fault
1 = Fault 0 = No fault
MAINB
MAIN Enable Status
–
Slot B
VAUXB
VAUX Enable Status
–
Slot B
VAUXBF
12VMBF
12VBF
5VBF
3VBF
Overcurrent Fault: VAUXB supply B
Overcurrent Fault:
–
12V supply B
Overcurrent Fault: +12V supply B
Overcurrent Fault: 5V supply B
Overcurrent Fault: 3.3V supply B
Power-Up Default Value: 0000 0000
b
= 00
h
Command_Byte Value (R/W): 0000 0101
b
= 05
h
The power-up default value is 00
h
. Both slots are disabled upon power-up, i.e., all supply outputs are off. In response to an
overcurrent fault condition, writing a logical 1 back into the active (or set) bit position will clear the bit and de-assert /INT. The
status of the /FAULTB pin is not affected by reading the Status Register or by clearing active status bits.
Notes:
1.
If FAULTB has been set by an overcurrent condition on one or more of the MAIN outputs, the ONB input must go LOW to reset FAULTB.
If FAULTB has been set by a VAUXB overcurrent event, the AUXENB input must go LOW to reset FAULTB.
If an overcurrent has occurred on both a MAIN output and the VAUX output of slot B, both ONB and AUXENB of the slot must go low to reset
FAULTB.
Neither the FAULTB bit nor the /FAULTB pin is active when the MIC2593 power paths are controlled by the System Management Interface. When
using SMI power path control, the AUXENB and ONB pins for that slot must be tied to GND.
2.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2593-5BTQ | Dual-Slot PCI Hot Plug Controller |
| MIL-PRF-19500 | SEMICONDUCTOR DEVICE, TRANSISTOR, NPN, SILICON, LOW-POWER TYPES 2N2484, 2N2484UA, 2N2484UB, JAN, JANTX, JANTXV, JANS, JANHC, AND JANKC |
| MINISO-8 | 8-LEAD MINI SMALL OUTLINE |
| MJ2400 | Inrush Current Controllers |
| MJB32B | PNP SILICON POWER TRANSISTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2593-2BTQ TR | 功能描述:IC PCI HOT PLUG CTLR DUAL 48TQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2593-2YTQ | 功能描述:熱插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2593-2YTQ TR | 功能描述:熱插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2594-1BM | 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2594-1BM TR | 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。