參數資料
型號： MIC280-0YM6
廠商： MICREL INC
元件分類： 模擬信號調理
英文描述： Precision IttyBitty Thermal Supervisor
中文描述： SPECIALTY ANALOG CIRCUIT, PDSO6
封裝： LEAD FREE, SOT-23, 6 PIN
文件頁數： 8/23頁
文件大?。?/td> 226K
代理商： MIC280-0YM6
MIC280
Micrel
MIC280
8
November 2004
(D7) represents the sign: zero for positive temperatures and
one for negative temperatures. Table 3 shows examples of
the data format used by the MIC280 for temperatures:
Temperature
Binary
+127°C
0111 1111
+125°C
0111 1101
+25°C
0001 1001
+1°C
0000 0001
0°C
0000 0000
–1°C
1111 1111
–25°C
1110 0111
–125°C
1000 0011
–128°C
1000 0000
Table 3: Digital Temperature Format, High Bytes
Hex
7F
7D
19
01
00
FF
E7
83
80
Extended temperature resolution is provided for the external
zone. The high and low temperature limits and the measured
temperature for zone one are reported as 12-bit values stored
in a pair of 8-bit registers. The measured temperature, for
example, is reported in registers TEMP1h, the high-order byte,
and TEMP1l, the low-order byte. The values in the low-order
bytes are left-justified four-bit binary values representing
one-sixteenth degree increments. The A-D converter resolu-
tion for zone 1 is selectable from nine to twelve bits via the
configuration register. Low-order bits beyond the resolution
selected will be reported as zeroes. Examples of this format
are shown below in Table 4.
FAULT QUEUE
A set of fault queues (programmable digital filters) are pro-
vided in the MIC280 to prevent false tripping due to thermal
or electrical noise. Two bits, CONFIG[5:4], set the depth of
the fault queues. The fault queue setting then determines
the number of consecutive temperature events (TEMPx >
THIGHx or TEMPx < TLOWx) which must occur in order for
the condition to be considered valid. As an example, as-
sume CONFIG[5:4] is programmed with 10b. The measured
temperature for a given zone would have to exceed THIGHx
for four consecutive A/D conversions before /INT would be
asserted or the status bit set.
Like any filter, the fault queue function also has the effect
of delaying the detection of temperature events. In this ex-
ample, it would take 4 x t
CONV
to detect a temperature event.
The fault queue depth vs. CONFIG[5:4] of the configuration
register is shown in Table 5. Note: there is no fault queue
for over-temperature events (CRIT0 and CRIT1) or diode
faults. The fault queue applies only to high-temperature and
low-temperature events as determined by the THIGHx and
TLOWx registers. Any write to CONFIG will result in the fault
queues being purged and reset. Writes to any of the limit
registers, TLOWx or THIGHx, will result in the fault queue for
the corresponding zone being purged and reset.
CONFIG[5:4]
00
01
10
11
Table 5: Fault Queue Depth Settings
FAULT QUEUE
DEPTH
1 (Default)
2
4
6
Interrupt Generation
There are eight different conditions that will cause the MIC280
to set one of the bits in STATUS and assert its /INT output,
if so enabled. These conditions are listed in Table 6. Unlike
previous generations of thermal supervisor IC’s, there are no
interdependencies between any of these conditions. That is,
if CONDITION is true, the MIC280 will respond accordingly,
regardless of any previous or currently pending events.
Normally when a temperature event occurs, the corresponding
status bit will be set in STATUS, the corresponding interrupt
mask bit will be cleared, and /INT will be asserted. Clearing
the interrupt mask bit(s) prohibits continuous interrupt gen-
eration while the device is being serviced. (It is possible to
prevent events from clearing interrupt mask bits by setting
bits in the lock register. See Table 7 for Lockbit function-
ality.) A temperature event will only set bits in the status
register if it is specifically enabled by the corresponding bit
in the interrupt mask register. An interrupt signal will only
be generated on /INT if interrupts are also globally enabled
(IE =1 in CONFIG).
The MIC280 expects to be interrogated using the Alert Re-
sponse Address once it has asserted its interrupt output. Fol-
lowing an interrupt, a successful response to the A.R.A. or a
read operation on STATUS will cause /INT to be de-asserted.
STATUS will also be cleared by the read operation. Reading
STATUS following an interrupt is an acceptable substitute for
Extended Temperature,
Low Byte
0.0000
0.0625
0.1250
0.2500
0.5625
0.9375
Resolution
9 BITS
10 BITS
Binary
0000 0000
0000 0000
0000 0000
0100 0000
1000 0000
1100 0000
11 BITS
Binary
0000 0000
0000 0000
0010 0000
0100 0000
1000 0000
1110 0000
12 BITS
Binary
0000 0000
0001 0000
0010 0000
0100 0000
1001 0000
1111 0000
Binary
0000 0000
0000 0000
0000 0000
0000 0000
1000 0000
1000 0000
Hex
00
00
00
00
80
80
Hex
00
00
00
40
80
C0
Hex
00
00
20
40
80
E0
Hex
00
10
20
40
90
F0
Table 4: Digital Temperature Format, Low Bytes
相關PDF資料
PDF描述
MIC280-1YM6 Precision IttyBitty Thermal Supervisor
MIC280-3YM6 Precision IttyBitty Thermal Supervisor
MIC280-5YM6 Precision IttyBitty Thermal Supervisor
MIC280-7YM6 IGBT Modules up to 1200V SixPACK
MIC280 Precision IttyBitty Thermal Supervisor
相關代理商/技術參數
參數描述
MIC280-0YM6 TR 功能描述:板上安裝溫度傳感器 12-bit Local and Remote +/-4% -55 C to +125 C I2C Temperature Sensor in SOT23-6 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
MIC280-0YM6-TR 功能描述:SENSOR TEMPERATURE SMBUS SOT23-6 制造商:microchip technology 系列:IttyBitty? 包裝:剪切帶（CT） 零件狀態:有效 傳感器類型:數字，本地/遠程 檢測溫度 - 本地:-55°C ~ 125°C 檢測溫度 - 遠程:-55°C ~ 125°C 輸出類型:SMBus 電壓 - 電源:3 V ~ 3.6 V 分辨率:7 b（本地），11 b（遠程） 特性:輸出開關，可編程分辨率，關斷模式 精度 - 最高（最低）:±2°C（±2.5°C） 測試條件:0°C ~ 100°C（-55°C ~ 125°C） 工作溫度:-55°C ~ 125°C 封裝/外殼:SOT-23-6 供應商器件封裝:SOT-23-6 標準包裝:1
MIC280-1BM6 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述:
MIC280-1BM6 TR 功能描述:IC SUPERVISOR THERMAL SOT23-6 RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:IttyBitty® 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND
MIC280-1YM6 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*