- 您現在的位置：買賣IC網 > PDF目錄383607 > MIC2800-33YML (Micrel Semiconductor,Inc.) Digital Power Management IC 2MHz, 600mA DC/DC w/Dual 300mA/300mA Low VIN LDOs PDF資料下載
參數資料
| 型號： | MIC2800-33YML |
| 廠商： | Micrel Semiconductor,Inc. |
| 英文描述： | Digital Power Management IC 2MHz, 600mA DC/DC w/Dual 300mA/300mA Low VIN LDOs |
| 中文描述： | 數字電源管理IC，600mA的直流/直流瓦特2MHz的/雙300mA/300mA低VIN LDO的 |
| 文件頁數： | 17/21頁 |
| 文件大?。?/td> | 645K |
| 代理商： | MIC2800-33YML |
Micrel, Inc.
MIC2800
Application Notes
June 2006
17
M9999-061406
(408) 955-1690
The MIC2800 is a digital power management IC with a
single integrated buck regulator and two independent
low dropout regulators. LDO1 is a 300mA low dropout
regulator that is using power supplied by the on board
buck regulator. LDO2 is a 300mA low dropout regulator
using the supply from the input pin. The buck regulator is
a 600mA PWM power supply that utilizes a /LOWQ light
load mode to maximize battery efficiency in light load
conditions. This is achieved with a /LOWQ control pin
that when pulled low, shuts down all the biasing and
drive current for the PWM regulator, drawing only 20μA
of operating current. This allows the output to be
regulated through the LDO output, capable of providing
60mA of output current. This method has the advantage
of producing a clean, low current, ultra low noise output
in /LOWQ mode. During /LOWQ mode, the SW node
becomes high impedance, blocking current flow. Other
methods of reducing quiescent current, such as pulse
frequency modulation (PFM) or bursting techniques
create large amplitude, low frequency ripple voltages
that can be detrimental to system operation.
When more than 60mA is required, the /LOWQ pin can
be forced high, causing the MIC2800 to enter PWM
mode. In this case, the LDO output makes a "hand-off"
to the PWM regulator with virtually no variation in output
voltage. The LDO output then turns off allowing up to
600mA of current to be efficiently supplied through the
PWM output to the load.
VIN
Two input voltage pins provide power to the switch mode
regular and LDO2 separately. The LDO1 input voltage is
provided by the DC/DC LDO pin. VIN provides power to
the LDO section and the bias through an internal 6
resistor. Both VIN pins must be tied together.
For the switch mode regulator VIN provides power to the
MOSFET along with current limiting sensing. Due to the
high
switching
speeds,
recommended close to VIN and the power ground
(PGND) pin for bypassing. Please refer to layout
recommendations.
a
4.7μF
capacitor
is
LDO
The LDO pin is the output of the linear regulator and
should be connected to the output. In /LOWQ mode
(/LOWQ <0.2V), the LDO provides the output voltage. In
PWM mode (/LOWQ >1V) the LDO pin provides power
to LDO1.
LDO1
Regulated output voltage of LDO1. Power is provided by
the DCDC switching regulator. Recommended output
capacitance is 2.2μF.
LDO2
Regulated output voltage of LDO2. Power is provided by
VIN. Recommended output capacitance is 2.2μF.
EN
Both enable inputs are active high, requiring 1.0V for
guaranteed operation. EN1 provides logic control of both
the DCDC regulator and LDO1. EN2 provides logic
control for LDO2 only. The enable inputs are CMOS
logic and cannot be left floating.
The enable pins provide logic level control of the
specified outputs. When both enable pins are in the off
state, supply current of the device is greatly reduced
(typically <1μA). When the DCDC regulator is in the off
state, the output drive is placed in a "tri-stated" condition,
where both the high side P-channel MOSFET and the
low-side N-channel are in an “off” or non-conducting
state. Do not drive either of the enable pins above the
supply voltage.
Power-On Reset (POR)
The power-on reset output is an open-drain N-Channel
device, requiring a pull-up resistor to either the input
voltage or output voltage for proper voltage levels. The
POR output has a delay time that is programmable with
a capacitor from the CSET pin to ground. The delay time
can be programmed to be as long as 1 second.
/LOWQ
The /LOWQ pin provides a logic level control between
the internal PWM mode and the low noise linear
regulator mode. With /LOWQ pulled low (<0.2V),
quiescent current of the device is greatly reduced by
switching to a low noise linear regulator mode that has a
typical IQ of 20μA. In linear (LDO) mode the output can
deliver 60mA of current to the output. By placing /LOWQ
high (>1V), the device transitions into a constant
frequency PWM buck regulator mode. This allows the
device the ability to efficiently deliver up to 600mA of
output current at the same output voltage.
/LOWQ mode also limits the output load of both LDO1
and LDO2 to 10mA.
BIAS
The BIAS pin supplies the power to the internal control
and reference circuitry. The bias is powered from AVIN
through an internal 6
resistor. A small 0.1μF capacitor
is recommended for bypassing.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2800-ADJYML | Digital Power Management IC 2MHz, 600mA DC/DC w/Dual 300mA/300mA Low VIN LDOs |
| MIC2807 | RF PA Power Management IC 2MHz, 600mA DC/DC w/DAC Input and Bypass Switch, Dual Low Noise 200mA/30mA LDO Regulators |
| MIC281-0BM6 | Low-Cost IttyBitty Thermal Sensor IttyBitty |
| MIC281-0YM6 | Low-Cost IttyBitty Thermal Sensor IttyBitty |
| MIC281-1BM6 | Low-Cost IttyBitty Thermal Sensor IttyBitty |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2800-A4SYML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
| MIC2800-A4SYML TR | 功能描述:線性穩壓器 - 標準 DC-DC + 2 Linear Regulators with LowQ Mode (Lead Free) RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MIC280-0BM6 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MIC280-0BM6 TR | 功能描述:IC SUPERVISOR THERMAL SOT23-6 RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:IttyBitty® 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓撲:ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| MIC280-0BM6TR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。