- 您現在的位置：買賣IC網 > PDF目錄383607 > MIC281-2YM6 (MICREL INC) Low-Cost IttyBitty Thermal Sensor IttyBitty PDF資料下載
參數資料
| 型號： | MIC281-2YM6 |
| 廠商： | MICREL INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Low-Cost IttyBitty Thermal Sensor IttyBitty |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO6 |
| 封裝： | LEAD FREE, SOT-23, 6 PIN |
| 文件頁數： | 6/12頁 |
| 文件大小： | 171K |
| 代理商： | MIC281-2YM6 |
MIC281
Functional Description
Serial Port Operation
The MIC281 uses standard SMBus Write_Byte and Read_Byte
operations for communication with its host. The SMBus
Write_Byte operation involves sending the device’s slave
address (with the R/W bit low to signal a write operation),
followed by a command byte and the data byte. The SMBus
Read_Byte operation is a composite write and read operation:
the host first sends the device’s slave address followed by
the command byte, as in a write operation. A new start bit
must then be sent to the MIC281, followed by a repeat of the
Micrel
MIC281
6
November 2004
slave address with the R/W bit (LSB) set to the high (read)
state. The data to be read from the part may then be clocked
out. These protocols are shown in Figures 1 and 2.
The Command byte is eight bits (one byte) wide. This byte
carries the address of the MIC281 register to be operated
upon. The command byte values corresponding to the various
MIC281 registers are shown in Table 1. Other command byte
values are reserved, and should not be used.
S
1
0
0
1
A2 A1 A0
0
A
X
X
X
X
X
X
X
X
A
D4
D5
D6
D3 D2 D1 D0
D7
/A P
MIC281 Slave Address
DATA
CLK
Command Byte
Data Byte to MIC281
START
STOP
R/W = WRITE
ACKNOWLEDGE
ACKNOWLEDGE
NOT ACKNOWLEDGE
Master to slave transfer,
i.e., DATA driven by master.
Slave to master transfer,
i.e., DATA driven by slave.
Figure 1. Write_Byte Protocol
S
1
0
0
1
X
X
X
X
X
X
0
A
X
X
X
X
X
X
X
X
A
S
1
1
1
0
0
X
X
X
X
X
X
X
A
X
/A P
MIC281 Slave Address
DATA
CLK
Command Byte
MIC281 Slave Address
Data Read From MIC281
START
START
STOP
R/W = WRITE
R/W = READ
ACKNOWLEDGE
ACKNOWLEDGE
ACKNOWLEDGE
NOT ACKNOWLEDGE
Master to slave transfer,
i.e., DATA driven by master.
Slave to master transfer,
i.e., DATA driven by slave.
Figure 2. Read_Byte Protocol
Label
TEMP
CONFIG
MFG_ID
DEV_ID
Command Byte
Value
Read
01
h
03
h
FE
h
FF
h
Power-on
Default
Target Register
Description
Remote temperature result
Configuration
Manufacturer identification
Device and revision identification
Write
n/a
03
h
n/a
n/a
00
h
(0°C)
80
h
2A
h
0x
h
*
* The lower nibble contains the die revision level, e.g., Rev 0 = 00h.
Table 1. MIC281 Register Addresses
相關PDF資料 |
PDF描述 |
|---|---|
| MIC281-3BM6 | Low-Cost IttyBitty Thermal Sensor IttyBitty |
| MIC281-3YM6 | Low-Cost IttyBitty Thermal Sensor IttyBitty |
| MIC281-4BM6 | Low-Cost IttyBitty Thermal Sensor IttyBitty |
| MIC281-4YM6 | Low-Cost IttyBitty Thermal Sensor IttyBitty |
| MIC281-5BM6 | Low-Cost IttyBitty Thermal Sensor IttyBitty |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC281-2YM6 TR | 功能描述:板上安裝溫度傳感器 Local and Remote Temperature Sensor with I2C Temperature Sensor in SOT23-6 (Lead Free) RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MIC281-3BM6 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MIC281-3BM6 TR | 功能描述:IC SUPERVISOR THERMAL SOT23-6 RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:IttyBitty® 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| MIC281-3BM6TR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MIC281-3YM6 TR | 功能描述:板上安裝溫度傳感器 Local and Remote Temperature Sensor with I2C Temperature Sensor in SOT23-6 (Lead Free) RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。