- 您現在的位置：買賣IC網 > PDF目錄383607 > MIC29201-3.3WT (MICREL INC) 400mA Low-Dropout Voltage Regulator PDF資料下載
參數資料
| 型號： | MIC29201-3.3WT |
| 廠商： | MICREL INC |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 400mA Low-Dropout Voltage Regulator |
| 中文描述： | 3.3 V FIXED POSITIVE LDO REGULATOR, 0.75 V DROPOUT, SFM5 |
| 封裝： | LEAD FREE, TO-220, 5 PIN |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 415K |
| 代理商： | MIC29201-3.3WT |
MIC2920A/29201/29202/29204
Applications Information
Micrel, Inc.
M9999-021505
8
February 2005
or some other supply voltage. In determining a value for this
resistor, note that while the output is rated to sink 250μA, this
sink current adds to battery drain in a low battery condition.
Suggested values range from 100k to 1MΩ. The resistor is
not required if this output is unused.
Programming the Output Voltage
(MIC29202/29204)
The MIC29202/29204 may be programmed for any output
voltage between its 1.235V reference and its 26V maxi-
mum rating, using an external pair of resistors, as shown in
Figure 3.
The complete equation for the output voltage is
V
OUT
= V
REF
×
{ 1 + R
1
/R
2
} –
|
I
FB
|
R
1
where V
is the nominal 1.235 reference voltage and I
is
the Adjust pin bias current, nominally 20nA. The minimum rec-
ommended load current of 1μA forces an upper limit of 1.2MΩ
on the value of R
, if the regulator must work with no load (a
condition often found in CMOS in standby), I
will produce
a –2% typical error in V
which may be eliminated at room
temperature by trimming R
. For better accuracy, choosing R
2
= 100k reduces this error to 0.17% while increasing the resistor
program current to 12μA. Since the MIC29202/29204 typically
draws 110μA at no load with SHUTDOWN open-circuited, this
is a negligible addition. The MIC29204 may be pin-strapped
for 5V using the internal voltage divider by tying Pin 1 (output)
to Pin 2 (sense) and Pin 7 (Adjust) to Pin 6 (V Tap).
Configuring the MIC29201-3.3BM
For the MIC29201-3.3BM, the output (Pin 1) and sense pin
(pin 2),
must
be connected to ensure proper operation. They
are not connected internally.
Reducing Output Noise
In reference applications it may be advantageous to reduce
the AC noise present at the output. One method is to reduce
the regulator bandwidth by increasing the size of the output
capacitor. This is relatively inefficient, as increasing the capaci-
Figure 1. ERROR Output Timing
* SEE APPLICATIONS INFORMATION
External Capacitors
A 10μF (or greater) capacitor is required between the MIC2920A
output and ground to prevent oscillations due to instability. Most
types of tantalum or aluminum electrolytics will be adequate;
film types will work, but are costly and therefore not recom-
mended. Many aluminum electrolytics have electrolytes that
freeze at about –30°C, so solid tantalums are recommended
for operation below –25°C. The important parameters of the
capacitor are an effective series resistance of about 5Ω or
less and a resonant frequency above 500kHz. The value of
this capacitor may be increased without limit.
At lower values of output current, less output capacitance is
required for output stability. The capacitor can be reduced
to 2.2μF for current below 10mA or 1μF for currents below
1mA. Adjusting the MIC29202/29204 to voltages below 5V
runs the error amplifier at lower gains so that more output ca-
pacitance is needed. For the worst-case situation of a 500mA
load at 1.23V output (Output shorted to Adjust) a 47μF (or
greater) capacitor should be used.
The MIC2920A/29201 will remain in regulation with a mini-
mum load of 1mA. When setting the output voltage of the
MIC29202/29204 versions with external resistors, the current
through these resistors may be included as a portion of the
minimum load.
A 0.1μF capacitor should be placed from the MIC2920A input
to ground if there is more than 10 inches of wire between
the input and the AC filter capacitor or if a battery is used as
the input.
Error Detection Comparator Output
(MIC29201/MIC29204)
A logic low output will be produced by the comparator when-
ever the MIC29201/29204 output falls out of regulation by
more than approximately 5%. This figure is the comparator’s
built-in offset of about 75mV divided by the 1.235V reference
voltage. (Refer to the block diagram on Page 1). This trip level
remains “5% below normal” regardless of the programmed
output voltage of the MIC29201/29204. For example, the
error flag trip level is typically 4.75V for a 5V output or 11.4V
for a 12V output. The out of regulation condition may be due
either to low input voltage, extremely high input voltage, cur-
rent limiting, or thermal limiting.
Figure 1 is a timing diagram depicting the ERROR signal and
the regulated output voltage as the MIC29201/29204 input is
ramped up and down. The ERROR signal becomes valid (low)
at about 1.3V input. It goes high at about 5V input (the input
voltage at which V
= 4.75). Since the MIC29201/29204’s
dropout voltage is load-dependent (see curve in Typical Per-
formance Characteristics), the input voltage trip point (about
5V) will vary with the load current. The output voltage trip point
(approximately 4.75V) does not vary with load.
The error comparator has an NPN open-collector output which
requires an external pull-up resistor. Depending on system
requirements, this resistor may be returned to the 5V output
4.75V
ERROR
OUTPUT
VOLTAGE
VOLTAGE
INPUT
5V
1.3V
NOT *
VALID
NOT *
VALID
相關PDF資料 |
PDF描述 |
|---|---|
| MIC29201-3.3WU | 400mA Low-Dropout Voltage Regulator |
| MIC29201-3.3YM | 400mA Low-Dropout Voltage Regulator |
| MIC29201-4.8WT | 400mA Low-Dropout Voltage Regulator |
| MIC29201-4.8WU | 400mA Low-Dropout Voltage Regulator |
| MIC29201-5.0WT | 400mA Low-Dropout Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC29201-4.8BT | 功能描述:IC REG LDO 4.85V .4A TO-220-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3.8V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.3V @ 80mA 穩壓器數量:1 電流 - 輸出:80mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC29201-4.8BU | 功能描述:IC REG LDO 4.85V .4A TO-263-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3.8V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.3V @ 80mA 穩壓器數量:1 電流 - 輸出:80mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC29201-4.8BU TR | 功能描述:IC REG LDO 4.85V .4A TO-263-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3.8V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.3V @ 80mA 穩壓器數量:1 電流 - 輸出:80mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC29201-4.8WT | 功能描述:低壓差穩壓器 - LDO 400mA LDO Fixed Voltage + Flag + Shutdown (ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MIC29201-4.8WU | 功能描述:低壓差穩壓器 - LDO 400mA LDO Fixed Voltage + Flag + Shutdown (ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。