- 您現在的位置：買賣IC網 > PDF目錄383611 > MIC4721 (Micrel Semiconductor,Inc.) Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder, SOT315-1 (LQFP80), Reel Dry Pack, SMD, 13",Turned PDF資料下載
參數資料
| 型號： | MIC4721 |
| 廠商： | Micrel Semiconductor,Inc. |
| 英文描述： | Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder, SOT315-1 (LQFP80), Reel Dry Pack, SMD, 13",Turned |
| 中文描述： | 1.5A的2MHz的集成開關降壓穩壓器 |
| 文件頁數： | 8/19頁 |
| 文件大?。?/td> | 827K |
| 代理商： | MIC4721 |
Micrel, Inc.
MIC4721
Pin Descriptions
VIN
Two pins for VIN provide power to the source of the
internal P-channel MOSFET along with the current
limiting sensing. The VIN operating voltage range is from
2.7V to 5.5V. Due to the high switching speeds, a 10μF
capacitor should be placed close to VIN and power
ground (PGND) at each pin for bypassing. Please refer
to the section on layout recommendations.
May 2007
8
M9999-052907-A
BIAS
The bias (BIAS) provides power to the internal reference
and control sections of the MIC4721. A 10
resistor
from VIN to BIAS and a 0.1μF from BIAS to SGND is
required.
EN
The enable pin provides a logic level control of the
output. At a low level, the output is shut off and supply
current at the VIN pin is greatly reduced (typically <2μA).
A high level turns the output on. The enable pin must not
be driven above the supply voltage.
FB
The feedback pin (FB) connects to the negative input of
the internal error amplifier. The pin is connected to an
external resistor divider, which sets the output voltage.
A feedforward capacitor across the upper resistor in the
divider is recommended for most designs. To reduce
current draw, a 10K feedback resistor is recommended
from the output to the FB pin (R1). The large resistor
value and the parasitic capacitance of the FB pin can
cause a high frequency pole that can reduce the overall
system phase margin. By placing a feedforward
capacitor, these effects can be significantly reduced.
SW
The switch (SW) pin connects directly to the inductor
and provides the switching current necessary to operate
in PWM mode. Due to the high speed switching on this
pin, the switch node should be routed away from
sensitive nodes. This pin also connects to the cathode of
the free-wheeling diode.
PGOOD
The power good pin pulls low to indicate the output
voltage is within its regulation range. When power good
is low, then the output voltage is within ±10% of the set
regulation voltage. For output voltages greater or less
than 10%, the PGOOD pin is high. This should be
connected to the input supply through a pull up resistor.
A delay can be added by placing a capacitor from
PGOOD-to-ground.
PGND
Power ground (PGND) is the ground path for the
MOSFET drive current. The current loop for the power
ground should be as small as possible and separate
from the Signal ground (SGND) loop. Refer to the
section on layout recommendations for more details.
SGND
Signal ground (SGND) is the ground path for the biasing
and control circuitry. The current loop for the signal
ground should be separate from the power ground
(PGND) loop. Refer to the section on layout
recommendations for more details.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC4721YMM | Dual UART with 64-byte FIFO, SOT313-2 (LQFP48), Reel Pack, SMD, 13", Turned |
| MIC4722 | 3mm x 3mm 2.7MHz 3A PWM Buck Regulator |
| MIC4722YML | 3mm x 3mm 2.7MHz 3A PWM Buck Regulator |
| MIC4807 | 80V 8-Channel Addressable Low-Side Driver |
| MIC4807BN | 80V 8-Channel Addressable Low-Side Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC4721YMM | 功能描述:直流/直流開關調節器 1.5A 2MHz Buck Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MIC4721YMM TR | 功能描述:直流/直流開關調節器 1.5A 2MHz Buck Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MIC4721YMMTR | 功能描述:IC REG BUCK ADJ 1.5A 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| MIC4722 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3mm x 3mm 2.7MHz 3A PWM Buck Regulator |
| MIC4722_10 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3mm x 3mm 2.7MHz 3A PWM Buck Regulator |
發布緊急采購，3分鐘左右您將得到回復。