- 您現在的位置：買賣IC網 > PDF目錄383612 > MIC49500-1.2WU (MICREL INC) 5A Dual Supply, Low Voltage, High Bandwidth LDO PDF資料下載
參數資料
| 型號： | MIC49500-1.2WU |
| 廠商： | MICREL INC |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 5A Dual Supply, Low Voltage, High Bandwidth LDO |
| 中文描述： | 1.2 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PSSO7 |
| 封裝： | ROHS COMPLIANT, TO-263, 7 PIN |
| 文件頁數： | 8/11頁 |
| 文件大小： | 233K |
| 代理商： | MIC49500-1.2WU |
Micrel, Inc.
MIC49500
Applications Information
The MIC49500 is an ultra-high performance, low
dropout linear regulator designed for high current
applications requiring fast transient response. The
MIC49500 utilizes two input supplies, significantly
reducing dropout voltage, perfect for low-voltage, DC-
to-DC conversion. The MIC49500 requires a minimum
of external components and obtains a bandwidth of up
to 10MHz. As a μCap regulator, the output is tolerant
of virtually any type of capacitor including ceramic and
tantalum.
November 2005
8
M9999-110805
(408) 955-1690
The MIC49500 regulator is fully protected from
damage due to fault conditions, offering constant
current limiting and thermal shutdown.
Bias Supply Voltage
V
BIAS
, requiring relatively light current, provides power
to the control portion of the MIC49500. V
BIAS
requires
approximately 70mA for 5A load current. Most of the
biasing current is used to supply the base current to
the pass transistor. This allows the pass element to be
driven into saturation, reducing the dropout to 290mV
at a 5A load current. Bypassing on the bias pin is
recommended to improve performance of the
regulator during line and load transients. Small
ceramic capacitors from V
BIAS
to ground help reduce
high frequency noise from being injected into the
control circuitry from the bias rail and are good design
practice. Good bypass techniques typically include
one larger capacitor such as 1μF ceramic and smaller
valued capacitors such as 0.01μF or 0.001μF in
parallel with that larger capacitor to decouple the bias
supply. The V
BIAS
input voltage must be 2.1V above
the output voltage with a minimum V
BIAS
input voltage
of 3.0V.
Input Supply Voltage
V
IN
provides the high current to the collector of the
pass transistor. The minimum input voltage is 1.4V,
allowing conversion from low voltage supplies.
Output Capacitor
The MIC49500 requires a minimum of output
capacitance to maintain stability. However, proper
capacitor selection is important to ensure desired
transient response. The MIC49500 is specifically
designed to be stable with a wide range of
capacitance values and ESR. A 10μF ceramic chip
capacitor should satisfy most applications. Output
capacitance can be increased without bound. See
typical characteristics for examples of load transient
response.
X7R dielectric ceramic capacitors are recommended
because of their temperature performance. X7R-type
capacitors change capacitance by 15% over their
operating temperature range and are the most stable
type of ceramic capacitors. Z5U and Y5V dielectric
capacitors change value by as much as 50% and
60%, respectively, over their operating temperature
ranges. To use a ceramic chip capacitor with Y5V
dielectric, the value must be much higher than an X7R
ceramic or a tantalum capacitor to ensure the same
capacitance value over the operating temperature
range. Tantalum capacitors have a very stable
dielectric (10% over their operating temperature
range) and can also be used with this device.
Input Capacitor
An input capacitor of 1μF or greater is recommended
when the device is more than 4 inches away from the
bulk supply capacitance, or when the supply is a
battery. Small, surface mount, ceramic chip capacitors
can be used for the bypassing. The capacitor should
be placed within 1" of the device for optimal
performance. Larger values will help to improve ripple
rejection by bypassing the input to the regulator,
further improving the integrity of the output voltage.
Thermal Design
Linear regulators are simple to use. The most
complicated design parameters to consider are
thermal characteristics. Thermal design requires the
following application-specific parameters:
Maximum ambient temperature (T
A
)
Output Current (I
OUT
)
Output Voltage (V
OUT
)
Input Voltage (V
IN
)
Ground Current (I
GND
)
First, calculate the power dissipation of the regulator
from these numbers and the device parameters from
this datasheet.
P
D
= V
IN
× I
IN
+ V
BIAS
× I
BIAS
– V
OUT
× I
OUT
The input current will be less than the output current
as the output load increases. The bias current is a
sum of base drive and ground current. Ground current
is constant over load current. Then the heat sink
thermal resistance is determined with this formula:
SA
=
T
J(MAX)
± T
A
P
D
JC
CS
)
相關PDF資料 |
PDF描述 |
|---|---|
| MIC49500WR | 5A Dual Supply, Low Voltage, High Bandwidth LDO |
| MIC49500WU | 5A Dual Supply, Low Voltage, High Bandwidth LDO |
| MIC5010 | Full-Featured High- or Low-Side MOSFET Driver |
| MIC5010BM | Full-Featured High- or Low-Side MOSFET Driver |
| MIC5010BN | Full-Featured High- or Low-Side MOSFET Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC49500WR | 功能描述:低壓差穩壓器 - LDO 5A LDO, Low Vin, Low Vout, Fast transient response, Cap stable (RoHS Compliant) RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MIC49500WR TR | 功能描述:低壓差穩壓器 - LDO 5A LDO, Low Vin, Low Vout, Fast transient response, Cap stable (RoHS Compliant) RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MIC49500WR-TR | 功能描述:Linear Voltage Regulator IC Positive Adjustable 1 Output 0.7 V ~ 6 V 5A S-PAK-7 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 穩壓器拓?fù)?正，可調式 電壓 - 輸出:0.7 V ~ 6 V 電流 - 輸出:5A 電壓 - 跌落（典型值）:0.29V @ 5A 穩壓器數:1 電壓 - 輸入:1.4 V ~ 6 V 電流 - 限制（最小值）:5.5A 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SPak-7（7 引線 + 接片） 供應商器件封裝:S-PAK-7 標準包裝:1 |
| MIC49500WU | 功能描述:低壓差穩壓器 - LDO 5A LDO, Low Vin, Low Vout, Fast transient response, Cap stable (RoHS Compliant) RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MIC49500WU TR | 功能描述:低壓差穩壓器 - LDO 5A LDO, Low Vin, Low Vout, Fast transient response, Cap stable (RoHS Compliant) RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。