參數資料
型號: MIC5010
廠商: Micrel Semiconductor,Inc.
英文描述: Full-Featured High- or Low-Side MOSFET Driver
中文描述: 全功能高或低側MOSFET驅動器
文件頁數: 13/16頁
文件大小: 189K
代理商: MIC5010
April 1998
5-99
MIC5010
Applications Information
(Continued)
Micrel
5
cross conduction. Both the top- and bottom-side drivers are
protected, so the output can be shorted to either rail without
damage.
The top-side driver is based on the bootstrapped circuit of
Figure 6, and cannot be switched on indefinitely. The
bootstrap capacitor (1
μ
F) relies on being pulled to ground
by the bottom-side output to recharge. This limits the
maximum duty cycle to slightly less than 100%.
Two of these circuits can be connected together to form an
H-bridge. If the H-bridge is used for locked antiphase
control, no special considerations are necessary. In the
case of sign/magnitude control, the “sign” leg of the H-
bridge should be held low (PWM input held low) while the
other leg is driven by the magnitude signal.
If current feedback is required for torque control, it is
available in chopped form at the bottom-side driver's 22m
current-sensing resistor.
Time-Delay Relay
(Figure 12). The MIC5010 forms the
basis of a simple time-delay relay. As shown, the delay
commences when power is applied, but the 100k
/1N4148
could be independently driven from an external source such
as a switch or another high-side driver to give a delay
relative to some other event in the system.
Hysteresis has been added to guarantee clean switching at
turn-on. Note that an over-current condition latches the
relay in a safe, OFF condition. Operation is restored by
either cycling power or by momentarily shorting pin 3 to
ground.
Motor Driver with Stall Shutdown
(Figure 13). Tachom-
eter feedback can be used to shut down a motor driver
circuit when a stall condition occurs. The control switch is a
3-way type; the “START” position is momentary and forces
the driver ON. When released, the switch returns to the
“RUN” position, and the tachometer's output is used to hold
the MIC5010 input ON. If the motor slows down, the tach
output is reduced, and the MIC5010 switches OFF. Resis-
tor “R” sets the shutdown threshold. If the output current
exceeds 30A, the MIC5010 shuts down and remains in that
condition until the momentary “RESET” button is pushed.
Control is then returned to the START/RUN/STOP switch.
Inhibit
Input
Thresh
Sense
Source
Gnd
Fault
V+
C1
Com
C2
Gate
1
2
3
4
5
6
7
8
9
10
11
12
13
14
MIC5010
IRFP250
100μF
6.2k
Figure 10. High-Voltage
Bootstrapped Driver
+
NC
NC
10m
KC1000-4T
(Kelvin)
1N4003
90V
100k
1k
100k
4N35
33k
33pF
MPSA05
10mA
Control Input
M
1nF
15V
1N4003 (2)
15Vp-p, 20kHz
Squarewave
1N4746
100nF
200V
1/4 HP, 90V
5BPB56HAA100
(GE)
相關PDF資料
PDF描述
MIC5010BM Full-Featured High- or Low-Side MOSFET Driver
MIC5010BN Full-Featured High- or Low-Side MOSFET Driver
MIC5013 Protected High- or Low-Side MOSFET Driver(帶過流保護的高/低邊MOS場效應管驅動器)
MIC5013BM FPGA 1000000 SYSTEM GATE 1.8 VOLT - NOT RECOMMENDED for NEW DESIGN
MIC5013BN FPGA 1000000 SYSTEM GATE 1.8 VOLT - NOT RECOMMENDED for NEW DESIGN
相關代理商/技術參數
參數描述
MIC5010BM 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Full-Featured High- or Low-Side MOSFET Driver
MIC5010BN 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Full-Featured High- or Low-Side MOSFET Driver
MIC5011 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Minimum Parts High- or Low-Side MOSFET Driver
MIC5011_05 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Minimum Parts High- or Low-Side MOSFET Driver
MIC5011BM 功能描述:IC DRIVER MIN PARTS HI/LO 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET,電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:高端 輸入類型:非反相 延遲時間:200ns 電流 - 峰:250mA 配置數:1 輸出數:1 高端電壓 - 最大(自引導啟動):600V 電源電壓:12 V ~ 20 V 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-DIP 包裝:管件 其它名稱:*IR2127