- 您現在的位置：買賣IC網 > PDF目錄358181 > MIC5201-3.0YSTR (MICREL INC) 3 V FIXED POSITIVE LDO REGULATOR, 0.4 V DROPOUT, PDSO3 PDF資料下載
參數資料
| 型號： | MIC5201-3.0YSTR |
| 廠商： | MICREL INC |
| 元件分類： | 固定正電壓單路輸出LDO穩壓器 |
| 英文描述： | 3 V FIXED POSITIVE LDO REGULATOR, 0.4 V DROPOUT, PDSO3 |
| 封裝： | LEAD FREE, SOT-223, 4 PIN |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 1003K |
| 代理商： | MIC5201-3.0YSTR |
MIC5201
Applications Information
Figure 1 shows a basic fixed-voltage application with the
unused enable input connected to V
IN
.
MIC5201-x.xBM
MIC5201-x.xBS
IN
EN
Micrel, Inc.
MIC5201
8
June 2005
OUT
GND
1
μ
F
V
IN
V
OUT
Figure 1. Fixed Application
Adjustable regulators require two resistors to set the output
voltage. See Figure 2.
MIC5201BM
IN
EN
OUT
ADJ
GND
V
IN
3.3
μ
F
V
OUT
R1
R2
V
1.242V 1
R2
R1
OUT
=
+
Figure 2. Adjustable Application
Resistors values are not critical because ADJ (adjust) has a
high impedance, but for best results use resistors of 470k
or less.
Output Capacitors
A 1
F capacitor is recommended between the MIC5201
output and ground to prevent oscillations due to instability.
Larger values serve to improve the regulator’s transient
response. Most types of tantalum or aluminum electrolytics
will be adequate; film types will work, but are costly and
therefore not recommended. Many aluminum electrolytics
have electrolytes that freeze at about –30
C, so solid tanta-
lums are recommended for operation below –25
C. The
important parameters of the capacitor are an effective series
resistance of about 5
or less and a resonant frequency
above 500kHz. The value of this capacitor may be increased
without limit.
At lower values of output current, less output capacitance is
required for output stability. The capacitor can be reduced to
0.47
μ
F for current below 10mA or 0.33
μ
F for currents below
1mA.
Input Capacitors
A 1
F capacitor should be placed from the MIC5201 input to
ground if there is more than 10 inches of wire between the
input and the ac filter capacitor or if a battery is used as the
input.
Noise Reduction Capacitors
On adjustable devices, a capacitor from ADJ to GND will
decrease high-frequency noise on the output. See Figure 3.
MIC5201BM
IN
EN
OUT
ADJ
GND
V
IN
3.3
μ
F
V
OUT
R1
R2
C
ADJ
Figure 3. Decreasing Ouput Noise
Minimum Load
The MIC5201 will remain stable and in regulation with no
load unlike many other voltage regulators. This is
especially important in CMOS RAM keep-alive
applications.
Dual-Supply Systems
When used in dual supply systems where the regulator
load is returned to a negative supply, the output voltage
must be diode clamped to ground.
Thermal Considerations Layout
The MIC5201-x.xBM (8-pin surface mount package) has the
following thermal characteristics when mounted on a single
layer copper-clad printed circuit board.
Multilayer boards having a ground plane, wide traces near the
pads, and large supply bus lines provide better thermal
conductivity.
The “worst case” value of 160
C/W assumes no ground
plane, minimum trace widths, and a FR4 material board.
Nominal Power Dissipation and Die Temperature
The MIC5201-x.xBM at a 25
C ambient temperature will
operate reliably at up to 625mW power dissipation when
mounted in the “worst case” manner described above. At an
ambient temperature of 55
C, the device may safely dissi-
pate 440mW. These power levels are equivalent to a die
temperature of 125
C, the recommended maximum tem-
perature for non-military grade silicon integrated circuits.
For MIC5201-x.xBS (SOT-223 package) heat sink character-
istics, please refer to Micrel Application Hint 17,
P.C. Board
Heat Sinking
.
245 mil
30 mil
50 mil
50 mil
150 mil
Figure 4. Min. Recommended SO-8 PCB Pads Size
PC Board
Dielectric
FR4
Ceramic
160oC/W
120oC/W
θ
JA
相關PDF資料 |
PDF描述 |
|---|---|
| MIC5201-3.3YMTR | 3.3 V FIXED POSITIVE LDO REGULATOR, 0.4 V DROPOUT, PDSO8 |
| MIC5201-3.3YSTR | 3.3 V FIXED POSITIVE LDO REGULATOR, 0.4 V DROPOUT, PDSO3 |
| MIC5201-4.8YSTR | 4.8 V FIXED POSITIVE LDO REGULATOR, 0.4 V DROPOUT, PDSO3 |
| MIC5201-5.0YMTR | 5 V FIXED POSITIVE LDO REGULATOR, 0.4 V DROPOUT, PDSO8 |
| MIC5203-2.8BM5TR | 2.8 V FIXED POSITIVE LDO REGULATOR, 0.6 V DROPOUT, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC5201-4.8BM | 功能描述:IC REG LDO 4.8V .2A 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3.8V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.3V @ 80mA 穩壓器數量:1 電流 - 輸出:80mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5201-4.8BM TR | 功能描述:IC REG LDO 4.8V .2A 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3.8V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.3V @ 80mA 穩壓器數量:1 電流 - 輸出:80mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5201-4.8BS | 功能描述:IC REG LDO 4.8V .2A SOT223 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3.8V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.3V @ 80mA 穩壓器數量:1 電流 - 輸出:80mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5201-4.8BS TR | 功能描述:IC REG LDO 4.8V .2A SOT-223 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3.8V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.3V @ 80mA 穩壓器數量:1 電流 - 輸出:80mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5201-4.8YM | 功能描述:低壓差穩壓器 - LDO 200mA, 1% LDO Regulator (Lead Free) RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。