- 您現在的位置：買賣IC網 > PDF目錄2159 > MIC7300YM5 TR (Micrel Inc)IC OP AMP R-R IN/OUT SOT23-5 PDF資料下載
參數資料
| 型號： | MIC7300YM5 TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 11/12頁 |
| 文件大小： | 0K |
| 描述： | IC OP AMP R-R IN/OUT SOT23-5 |
| 標準包裝： | 1 |
| 系列： | IttyBitty® |
| 放大器類型： | 通用 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.5 V/µs |
| 增益帶寬積： | 370kHz |
| 電流 - 輸入偏壓： | 0.5pA |
| 電壓 - 輸入偏移： | 1000µV |
| 電流 - 電源： | 1.5mA |
| 電流 - 輸出 / 通道： | 115mA |
| 電壓 - 電源，單路/雙路(±)： | 2.2 V ~ 10 V，±1.1 V ~ 5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SC-74A，SOT-753 |
| 供應商設備封裝： | SOT-23-5 |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1111 (CN2011-ZH PDF) |
| 其它名稱： | 576-1319-6 |
MIC7300
Micrel
MIC7300
8
June 2005
Application Information
Input Common-Mode Voltage
The MIC7300 tolerates input overdrive by at least 300mV
beyond either rail without producing phase inversion.
If the absolute maximum input voltage is exceeded, the input
current should be limited to
±5mA maximum to prevent
reducing reliability. A 10k
series input resistor, used as a
current limiter, will protect the input structure from voltages as
large as 50V above the supply or below ground. See Figure
1.
VIN
VOUT
10k
RIN
Figure 1. Input Current-Limit Protection
Output Voltage Swing
Sink and source output resistances of the MIC7300 are
equal. Maximum output voltage swing is determined by the
load and the approximate output resistance. The output
resistance is:
R
V
I
OUT
DROP
LOAD
=
V
DROP is the voltage dropped within the amplifier output
stage. V
DROP and ILOAD can be determined from the VO
(output swing) portion of the appropriate Electrical Character-
istics table. I
LOAD is equal to the typical output high voltage
minus V+/2 and divided by R
LOAD. For example, using the
Electrical Characteristics DC (5V) table, the typical output
high voltage using a 2k
load (connected to V+/2) is 4.985V,
which produces an I
LOAD of:
4.985V
2.5V
2k
1.243mA
=
.
Voltage drop in the amplifier output stage is:
V
DROP = 5.0V – 4.985V
V
DROP = 0.015V
Because of output stage symmetry, the corresponding typical
output low voltage (0.015V) also equals V
DROP. Then:
R
0.015V
0.001243A
1
OUT == 2
Power Dissipation
The MIC7300 output drive capability requires considering
power dissipation. If the load impedance is low, it is possible
to damage the device by exceeding the 125
°C junction
temperature rating.
On-chip power consists of two components: supply power
and output stage power. Supply power (P
S) is the product of
the supply voltage (V
S = VV+ – VV–) and supply current (IS).
Output stage power (P
O) is the product of the output stage
voltage drop (V
DROP) and the output (load) current (IOUT).
Total on-chip power dissipation is:
P
D = PS + PO
P
D = VS IS + VDROP IOUT
where:
P
D = total on-chip power
P
S = supply power dissipation
P
O = output power dissipation
V
S = VV+ – VV–
I
S = power supply current
V
DROP = VV+ – VOUT
(sourcing current)
V
DROP = VOUT – VV–
(sinking current)
The above addresses only steady state (dc) conditions. For
non-dc conditions the user must estimate power dissipation
based on rms value of the signal.
The task is one of determining the allowable on-chip power
dissipation for operation at a given ambient temperature and
power supply voltage. From this determination, one may
calculate the maximum allowable power dissipation and,
after subtracting P
S, determine the maximum allowable load
current, which in turn can be used to determine the miniumum
load impedance that may safely be driven. The calculation is
summarized below.
P
TT
D(max)
J(max)
A
JA
=
θ
JA(SOT-23-5) = 260°C/W
θ
JA(MSOP-8) = 85°C/W
Driving Capacitive Loads
Driving a capacitive load introduces phase-lag into the output
signal, and this in turn reduces op-amp system phase margin.
The application that is least forgiving of reduced phase
margin is a unity gain amplifier. The MIC7300 can typically
drive a 2500pF capacitive load connected directly to the
output when configured as a unity-gain amplifier and pow-
ered with a 2.2V supply. At 10V operation the circuit typically
drives 6000pF. Phase margin is typically 40
°.
Using Large-Value Feedback Resistors
A large-value feedback resistor (> 500k
) can reduce the
phase margin of a system. This occurs when the feedback
resistor acts in conjunction with input capacitance to create
phase lag in the feedback signal. Input capacitance is usually
a combination of input circuit components and other parasitic
capacitance, such as amplifier input capacitance and stray
printed circuit board capacitance.
Figure 2 illustrates a method of compensating phase lag
caused by using a large-value feedback resistor. Feedback
capacitor C
FB introduces sufficient phase lead to overcome
相關PDF資料 |
PDF描述 |
|---|---|
| MIC860YC5 TR | IC OPAMP 4MHZ 2.7V ULT LP SC70-5 |
| MIC861BC5 TR | IC OPAMP 400KHZ 2.7V ULT LP SC70 |
| MIC862YM8 TR | IC OPAMP DUAL 3MHZ 2V SOT23-8 |
| MIC863YM8 | IC OPAMP DUAL 450KHZ 2V SOT23-8 |
| MIC910BM5 TR | IC OPAMP 135MHZ 2.4MA HS SOT23-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC7300YMM | 功能描述:運算放大器 - 運放 2.2V, IttyBitty Op-Amp with High Drive Capability - Lead Free RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MIC7300YMM TR | 功能描述:運算放大器 - 運放 2.2V, IttyBitty Op-Amp with High Drive Capability - Lead Free RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MIC74 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:TXRX_982_R1 Evaluation Board |
| MIC74_06 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Wire Serial I/O Expander and Fan Controller |
| MIC7499221121 | 制造商:Wurth Electronics Inc 功能描述:1x2 100Base-T Dual Port With LED Shielded Tabs RJ45 Modular Jack |
發布緊急采購，3分鐘左右您將得到回復。