- 您現在的位置：買賣IC網 > PDF目錄383616 > MIC910BM5 (MICREL INC) 135MHz Low-Power SOT-23-5 Op Amp PDF資料下載
參數資料
| 型號： | MIC910BM5 |
| 廠商： | MICREL INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | 135MHz Low-Power SOT-23-5 Op Amp |
| 中文描述： | OP-AMP, 15000 uV OFFSET-MAX, 125 MHz BAND WIDTH, PDSO5 |
| 封裝： | SOT-23, 5 PIN |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 552K |
| 代理商： | MIC910BM5 |
June 2000
9
MIC910
MIC910
Applications Information
The MIC910 is a high-speed, voltage-feedback operational
amplifier featuring very low supply current and excellent
stability. This device is unity gain stable and capable of
driving high capacitance loads.
Driving High Capacitance
The MIC910 is stable when driving any capacitance (see
“
Typical Characteristics: Gain Bandwidth and Phase Margin
vs. Load Capacitance
”
) making it ideal for driving long coaxial
cables or other high-capacitance loads.
Phase margin remains constant as load capacitance is
increased. Most high-speed op amps are only able to drive
limited capacitance.
Note: increasing load capacitance does reduce the
speed of the device (see
“
Typical Characteris-
tics: Gain Bandwidth and Phase Margin vs.
Load
”
). In applications where the load capaci-
tance reduces the speed of the op amp to an
unacceptable level, the effect of the load capaci-
tance can be reduced by adding a small resistor
(<100
) in series with the output.
Feedback Resistor Selection
Conventional op amp gain configurations and resistor selec-
tion apply, the MIC910 is NOT a current feedback device.
Resistor values in the range of 1k to 10k are recommended.
Layout Considerations
All high speed devices require careful PCB layout. The high
stability and high PSRR of the MIC910 make this op amp
easier to use than most, but the following guidelines should
be observed: Capacitance, particularly on the two inputs pins
will degrade performance; avoid large copper traces to the
inputs. Keep the output signal away from the inputs and use
a ground plane.
It is important to ensure adequate supply bypassing capaci-
tors are located close to the device.
Micrel
Power Supply Bypassing
Regular supply bypassing techniques are recommended. A
10
μ
F capacitor in parallel with a 0.1
μ
F capacitor on both the
positive and negative supplies are ideal. For best perfor-
mance all bypassing capacitors should be located as close to
the op amp as possible and all capacitors should be low ESL
(equivalent series inductance), ESR (equivalent series resis-
tance). Surface-mount ceramic capacitors are ideal.
Thermal Considerations
The SOT-23-5 package, like all small packages, has a high
thermal resistance. It is important to ensure the IC does not
exceed the maximum operating junction (die) temperature of
85
°
C. The part can be operated up to the absolute maximum
temperature rating of 125
°
C, but between 85
°
C and 125
°
C
performance will degrade, in particular CMRR will reduce.
A MIC910 with no load, dissipates power equal to the quies-
cent supply current * supply voltage
(
When a load is added, the additional power is dissipated in
the output stage of the op amp. The power dissipated in the
device is a function of supply voltage, output voltage and
output current.
(
P
V
V
I
D
V
V
S
(noload)
=
)
+
P
V
V
I
D
V
OUT
OUT
(output stage)
=
)
+
TotalPower Dissipation
P
P
D
D
=
+
(noload)
(outpu stage)
Ensure the total power dissipated in the device is no greater
than the thermal capacity of the package. The SOT23-5
package has a thermal resistance of 260
°
C/W.
Max AllowablePower Dissipation
.
T
T
J
A
=
(max)
(max)
260W
相關PDF資料 |
PDF描述 |
|---|---|
| MIC911 | 105MHz Low-Power SOT-23-5 Op Amp |
| MIC911BM5 | 5000 SYSTEM GATE 3.3 VOLT LOGIC CELL ARR - NOT RECOMMENDED for NEW DESIGN |
| MIC912 | 200MHz Low-Power SOT-23-5 Op Amp |
| MIC912BM5 | 10000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
| MIC913 | 10000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC910BM5 TR | 功能描述:IC OPAMP 135MHZ 2.4MA HS SOT23-5 RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| MIC910YM5 TR | 功能描述:運算放大器 - 運放 135MHz, 2.4mA High Speed Op Amp (Lead Free) RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MIC910YM5TR | 制造商:Micrel Inc 功能描述:Op Amp,135MHz,2.4mA,+/-2.5 to+/-9V SOT23 |
| MIC910YM5-TR | 功能描述:Voltage Feedback Amplifier 1 Circuit SOT-23-5 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:Last Time Buy 放大器類型:電壓反饋 電路數:1 輸出類型:- 壓擺率:270 V/μs 增益帶寬積:135MHz -3db 帶寬:- 電流 - 輸入偏置:3.5μA 電壓 - 輸入失調:1mV 電流 - 電源:2.5mA 電流 - 輸出/通道:90mA 電壓 - 電源，單/雙（±）:±2.5 V ~ 9 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商器件封裝:SOT-23-5 標準包裝:1 |
| MIC911 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:105MHz Low-Power SOT-23-5 Op Amp |
發布緊急采購，3分鐘左右您將得到回復。