- 您現在的位置：買賣IC網 > PDF目錄383616 > MIC913 (Micrel Semiconductor,Inc.) 10000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN PDF資料下載
參數資料
| 型號： | MIC913 |
| 廠商： | Micrel Semiconductor,Inc. |
| 英文描述： | 10000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
| 中文描述： | 350MHz的低功耗的SOT - 23 - 5運算放大器 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 180K |
| 代理商： | MIC913 |
August 2000
11
MIC913
MIC913
Applications Information
The MIC913 is a high-speed, voltage-feedback operational
amplifier featuring very low supply current. The MIC913 is not
unity-gain stable, it requires a minimum gain of +2 or
–
1 to
ensure stability. The device is however stable even when
driving high capacitance loads.
Driving High Capacitance
The MIC913 is stable when driving any capacitance (see
“
Typical Characteristics: Gain Bandwidth and Phase Margin
vs. Load Capacitance
”
) making it ideal for driving long coaxial
cables or other high-capacitance loads.
Phase margin remains constant as load capacitance is
increased. Most high-speed op amps are only able to drive
limited capacitance.
Note: increasing load capacitance does reduce the
speed of the device (see
“
Typical Characteris-
tics: Gain Bandwidth and Phase Margin vs.
Load
”
). In applications where the load capaci-
tance reduces the speed of the op amp to an
unacceptable level, the effect of the load capaci-
tance can be reduced by adding a small resistor
(<100
) in series with the output.
Feedback Resistor Selection
Conventional op amp gain configurations and resistor selec-
tion apply, the MIC913 is NOT a current feedback device.
Resistor values in the range of 1k to 10k are recommended.
Layout Considerations
All high speed devices require careful PCB layout. The high
stability and high PSRR of the MIC913 make this op amp
easier to use than most, but the following guidelines should
be observed: Capacitance, particularly on the two inputs pins
will degrade performance; avoid large copper traces to the
inputs. Keep the output signal away from the inputs and use
a ground plane.
It is important to ensure adequate supply bypassing capaci-
tors are located close to the device.
Micrel
Power Supply Bypassing
Regular supply bypassing techniques are recommended. A
10
μ
F capacitor in parallel with a 0.1
μ
F capacitor on both the
positive and negative supplies are ideal. For best perfor-
mance all bypassing capacitors should be located as close to
the op amp as possible and all capacitors should be low ESL
(equivalent series inductance), ESR (equivalent series resis-
tance). Surface-mount ceramic capacitors are ideal.
Thermal Considerations
The SOT-23-5 package, like all small packages, has a high
thermal resistance. It is important to ensure the IC does not
exceed the maximum operating junction (die) temperature of
85
°
C. The part can be operated up to the absolute maximum
temperature rating of 125
°
C, but between 85
°
C and 125
°
C
performance will degrade, in particular CMRR will reduce.
A MIC913 with no load, dissipates power equal to the quies-
cent supply current * supply voltage
(
When a load is added, the additional power is dissipated in
the output stage of the op amp. The power dissipated in the
device is a function of supply voltage, output voltage and
output current.
(
P
V
V
I
D
V
V
S
(noload)
=
)
+
P
V
V
I
D
V
OUT
OUT
(output stage)
=
)
+
TotalPower Dissipation
P
P
D
D
=
+
(noload)
(outpu stage)
Ensure the total power dissipated in the device is no greater
than the thermal capacity of the package. The SOT23-5
package has a thermal resistance of 260
°
C/W.
Max.
T
T
J
A
=
(max)
(max)
260W
相關PDF資料 |
PDF描述 |
|---|---|
| MIC913BM5 | 10000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
| MIC914 | 160MHz Low-Power SOT-23-5 Op Amp |
| MIC914BM5 | 10000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
| MIC915 | 10000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
| MIC915BMM | 10000 SYSTEM GATE 3.3 VOLT LOGIC CELL AR - NOT RECOMMENDED for NEW DESIGN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC9130 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:High-Voltage, High-Speed Telecom DC-to-DC Controller |
| MIC9130_08 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:High-Voltage, High-Speed Telecom DC-to-DC Controller |
| MIC9130BM | 功能描述:IC CTRLR DC-DC PWM HV HS 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| MIC9130BM TR | 功能描述:IC CTRLR DC-DC PWM HV HS 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| MIC9130BQS | 功能描述:IC CTRLR DC-DC PWM HV HS 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。