- 您現在的位置：買賣IC網 > PDF目錄224285 > MICRF610TR (MICREL INC) 868-870 MHz ISM Band Transceiver Module PDF資料下載
參數資料
| 型號： | MICRF610TR |
| 廠商： | MICREL INC |
| 元件分類： | 通信及網絡 |
| 英文描述： | 868-870 MHz ISM Band Transceiver Module |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, QMA16 |
| 封裝： | 11.50 X 14.10 MM, MODULE-16 |
| 文件頁數： | 20/20頁 |
| 文件大?。?/td> | 698K |
| 代理商： | MICRF610TR |
Micrel, Inc.
MICRF610/MICRF610Z
July 2006
9
M9999-120205
How to write:
Bring CS high
Use SCLK and IO to clock in the 23 octets
Bring CS low
Refer to the figure in the next section, “Writing to n
registers having incremental addresses”.
Writing to n Registers Having Incremental Addresses
In addition to entering all bytes, it is also possible to enter
a set of n bytes, starting from address i = “A6, A5, … A0”.
Typical example: Clock in a new set of frequency dividers
(i.e. change the RF frequency). “Incremental addresses”.
Registers to be written are located in i, i+1, i+2.
What to write:
Field
Comments
Address:
7 bit = A6, A5, …A0 (A6 = msb. A0 = lsb) (address of first byte to
write to)
R/W bit:
“0” for writing
Values:
n* 8 bits =
D7, D6, …D0 (D7 = msb, D0 = lsb) (written to control reg. with
address ”i”)
D7, D6, …D0 (D7 = msb, D0 = lsb) (written to control reg. with
address ”i+1”)
D7, D6, …D0 (D7 = msb, D0 = lsb) (written to control reg. with
address ”i+n-1”)
Table 5. “Address” and “R/W bit” together make 1 octet.
In addition, n octets with programming bits are entered.
Totally. 1 +n octets are clocked into the MICRF610.
How to write:
Bring CS high
Use SCLK and IO to clock in the 1 + n octets
Bring CS low
In Figure 1, IO is changed at positive edges of SCLK. The
MICRF610 samples the IO line at negative edges. The
value of the R/W bits is always “0” for writing.
CS
SCLK
IO
A6
A5
A0
RW
D7
D6
D2
D1
D0
Address of first
RW
register to write to,
register i
Data to write
into register i
Internal load pulse made here
Data to write
into register i+1
Figure 2. How to write to many Control Registers
Reading from the Control Registers in MICRF610
The “read-sequence” is:
1. Enter address and R/W bit
2. Change direction of IO line
3. Read out a number of octets and change IO
direction back again.
It is possible to read all, 1 or n registers. The address to
read from (or the first address to read from) can be any
valid address (0-22). Reading is not destructive, i.e. values
are not changed. The IO line is output from the MICRF610
(input to user) for a part of the read-sequence. Refer to
procedure description below.
A read-sequence is described for reading n registers,
where n is number 1-23.
Reading n Registers from MICRF610
CS
SCLK
IO
A6
A5
A0
RW D7
D6
D0
Address of register i
RWData read from reg. i
Simple time
IO Input
IO Output
Figure 3. How to read from many Control Registers
In Figure 3, 1 register is read. The address is A6, A5, …
A0. A6 = msb. The data read out is D7, D6, …D0. The
value of the R/W bit is always “1” for reading.
SCLK and IO together form a serial interface. SCLK is
applied externally for reading as well as for writing.
Bring CS active
Enter address to read from (or the first address to
read from) (7 bits) and
The R/W bit = 1 to enable reading
Make the IO line an input to the user (set pin in
tristate)
Read n octets. The first rising edge of SCLK will
set the IO as an output from the MICRF610.
MICRF will change the IO line at positive edges.
The user should read the IO line at the negative
edges.
Make the IO line an output from the user again.
相關PDF資料 |
PDF描述 |
|---|---|
| MICRF610 | 868-870 MHz ISM Band Transceiver Module |
| MIK0-55S | 55 CONTACT(S), POLYETHYLENE, FEMALE, CIRCULAR CONNECTOR, CRIMP, RECEPTACLE |
| MIK0-7S | 7 CONTACT(S), POLYETHYLENE, FEMALE, CIRCULAR CONNECTOR, CRIMP, RECEPTACLE |
| MIK6-55P | 55 CONTACT(S), POLYETHYLENE, MALE, CIRCULAR CONNECTOR, CRIMP, PLUG |
| MIK6-7P | 7 CONTACT(S), POLYETHYLENE, MALE, CIRCULAR CONNECTOR, CRIMP, PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MICRF610Z | 功能描述:IC RF MOD 868-870MHZ 11.5X14.1MM RoHS:是 類別:RF/IF 和 RFID >> RF 收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:30 系列:- 頻率:4.9GHz ~ 5.9GHz 數據傳輸率 - 最大:54Mbps 調制或協議:* 應用:* 功率 - 輸出:-3dBm 靈敏度:- 電源電壓:2.7 V ~ 3.6 V 電流 - 接收:* 電流 - 傳輸:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 工作溫度:-25°C ~ 85°C 封裝/外殼:68-TQFN 裸露焊盤 包裝:管件 |
| MICRF610Z TR | 功能描述:IC RF MOD 868-870MHZ 11.5X14.1MM RoHS:是 類別:RF/IF 和 RFID >> RF 收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:30 系列:- 頻率:4.9GHz ~ 5.9GHz 數據傳輸率 - 最大:54Mbps 調制或協議:* 應用:* 功率 - 輸出:-3dBm 靈敏度:- 電源電壓:2.7 V ~ 3.6 V 電流 - 接收:* 電流 - 傳輸:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 工作溫度:-25°C ~ 85°C 封裝/外殼:68-TQFN 裸露焊盤 包裝:管件 |
| MICRF620 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:434MHz ISM Band Transceiver Module |
| MICRF620_0608 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:434MHz ISM Band Transceiver Module |
| MICRF620DEV1 | 制造商:Micrel Inc 功能描述:DEVELOPMENT KIT TRANSCEIVER 433MHZ |
發布緊急采購，3分鐘左右您將得到回復。