- 您現在的位置：買賣IC網 > PDF目錄9671 > MK1575-01GLF (IDT, Integrated Device Technology Inc)IC CLK RECOVERY PLL 16-TSSOP PDF資料下載
參數資料
| 型號： | MK1575-01GLF |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLK RECOVERY PLL 16-TSSOP |
| 標準包裝： | 96 |
| 類型： | 時鐘和數據恢復（CDR），多路復用器 |
| PLL： | 是 |
| 主要目的： | 視頻 |
| 輸入： | 時鐘 |
| 輸出： | LVCMOS |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:2 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 80MHz |
| 電源電壓： | 3.15 V ~ 3.45 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
| 其它名稱： | 800-2259 MK1575-01GLF-ND |
MK1575-01
CLOCK RECOVERY PLL
CLOCK SYNTHESIZER
IDT CLOCK RECOVERY PLL
7
MK1575-01
REV P 051310
0.68
μF
Panasonic ECP-U1C684MA5 (SMT film type, 1206 size, available from DigiKey)
10
μF
MuRata GRM42-2X5R106K10
10 nF
Panasonic ECH-U1C103JB5 (SMT film type, 805 size, available from DigiKey)
33 nF
Panasonic ECH-U1C333JB5 (SMT film type, 1206 size, available from DigiKey)
Input-to-Output Skew Induced by Loop Filter
Leakage
Leakage across the loop filter, due to PCB contamination or
poor quality loop filter capacitors, can increase
input-to-output clock skew error. Concern regarding
input-to-output skew error is usually limited to “zero delay”
configurations, where CLK1 or CLK2 is directly connected to
FBIN. In sever cases of loop filter leakage, however, output
clock jitter can also be increased.
The capacitors CS and CP in the external loop filter maintain
the VCO frequency control voltage between charge pump
pulses, which by design coincide with phase detector
events. VCO frequency or phase adjustments are made by
these charge pump pulses, pumping current into (or out of)
the external loop filter capacitors to adjust the VCO control
voltage as needed. Like the capacitors, the CHGP pin (pin
8) is a high-impedance PLL node; the charge pump is a
current source, which is high impedance by definition, and
the VCO input is also high impedance.
During normal (locked) operation, in the event of current
leakage in the loop filter, the charge pump will need to
deliver equal and opposite charge in the form of longer
charge pump pulses. The increased length of the charge
pump pulse will be translated directly to increased
input-to-output clock skew. This can also result in higher
output jitter due to higher reference clock feedthrough
(where the reference clock is fREFIN), depending on the loop
filter attenuation characterisitcs.
The Input-to-Output skew parameters in the DC Electrical
Specifications assume minimal loop filter leakage.
Additional skew due to loop filter leakage may be calculated
as follows:
Avoiding PLL Lockup
In some applications, the MK1575-01 VCO can “l(fā)ock up” at
it’s maximum operating frequency. To avoid this problem
observe the following rules:
1) Do not open the clock feedback path with the MK1575-01
enabled. If the MK1575-01 is enabled and does not get a
feedback clock into pin FBIN, the output frequency will be
forced to the maximum value by the PLL.
If an external divider is in the feedback path and it has a
delay before becoming active, hold the OE pin high until the
divider is ready to work. This could occur, for example, if the
divider is implemented in a FPGA.
Holding OE high powers down the MK1575-01 and dumps
the charge off the loop filter.
2) If an external divider is used in the feedback path, use a
circuit that can operate well beyond the intended output
clock frequency.
Power Supply Considerations
As with any integrated clock device, the MK1575-01 has a
special set of power supply requirements:
The feed from the system power supply must be filtered
for noise that can cause output clock jitter. Power supply
noise sources include the system switching power supply
or other system components. The noise can interfere with
device PLL components such as the VCO or phase
detector.
Each VDD pin must be decoupled individually to prevent
power supply noise generated by one device circuit block
from interfering with another circuit block.
Clock noise from device VDD pins must not get onto the
PCB power plane or system EMI problems may result.
Leakage Induced I/O Skew (sec)
I
Leakage
I
CP
F
REFIN
×
---------------------------------
=
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B2Y-MV-F1 | CONVERTER MOD DC/DC 3.3V 99W |
| MS3116P18-32S | CONN PLUG 32POS STRAIGHT W/SCKT |
| MS27474E24B61S | CONN RCPT 61POS JAM NUT W/SCKT |
| V48C24M150B | CONVERTER MOD DC/DC 24V 150W |
| VI-J44-MX-F4 | CONVERTER MOD DC/DC 48V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MK1575-01GLFTR | 功能描述:時鐘發生器及支持產品 CLOCK RECOVERY PLL RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| MK1575-01GTR | 功能描述:IC CLK RECOVERY PLL 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| MK1581-01 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:LOW PHASE NOISE T1/E1 CLOCK GENERATOR |
| MK1581-01GI | 功能描述:IC CLK GENERATOR T1/E1 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| MK1581-01GILF | 功能描述:時鐘發生器及支持產品 LOW PHASE NOISE T1/E 1 CLOCK GENERATOR RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
發布緊急采購，3分鐘左右您將得到回復。