- 您現在的位置：買賣IC網 > PDF目錄359169 > ML4769ES 2 Cell, Adjustable Output Boost Regulator with Load Disconnect PDF資料下載
參數資料
| 型號： | ML4769ES |
| 英文描述： | 2 Cell, Adjustable Output Boost Regulator with Load Disconnect |
| 中文描述： | 2細胞，可調輸出升壓穩壓器與負載斷開 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 240K |
| 代理商： | ML4769ES |
ML4769
7
DESIGN CONSIDERATIONS
(Continued)
In applications where the ML4769 is operated at or near
the maximum output current, it is recommended to add a
10nF to 100nF ceramic capacitor from V
OUT
to GND. The
optimum value of the high frequency bypass capacitor is
dependent on the layout and the value of the bulk output
capacitor selected.
INPUT CAPACITOR
Due to the high input current drawn at startup and
possibly during operation, it is recommended to decouple
the input with a capacitor with a value of 47μF to 100μF.
This filtering prevents the input ripple from affecting the
ML4769 control circuitry, and also improves the
efficiency by reducing the I
2
R losses during the charge
cycle of the inductor. Again, a low ESR capacitor (such as
tantalum) is recommended.
It is also recommended that low source impedance
batteries be used. Otherwise, the voltage drop across the
source impedance during high input current situations will
cause the ML4769 to fail to start up or to operate
unreliably. In general, for two cell applications the source
impedance should be less than 400m
W
, which means that
small alkaline cells should be avoided.
SHUTDOWN
The input levels of the SHDN pin are CMOS compatible.
To guarantee proper operation, SHDN must be pulled to
within 0.5V of GND or V
IN
to prevent excessive power
dissipation and possible oscillations.
SETTING THE OUTPUT VOLTAGE
The adjustable output of the ML4769 requires an external
feedback resistor divider to set V
OUT
. The output voltage
can be determined from the following equation:
V
R
(
R2
R2
OUT
=
+
257
.
1
)
(3)
where R1 and R2 are connected as shown in Figure 2. The
value of R2 should be 250k
W
or less to minimize bias
current errors. Choose an appropriate value for R2 and
calculate R1.
LAYOUT
Good layout practices will ensure proper operation of the
ML4769. Some layout guidelines follow:
Use adequate ground and power traces or planes
Keep components as close as possible to the ML4769
Use short trace lengths from the inductor to the V
L1
and
V
L2
pins and from the output capacitor to the V
OUT
pin
Use a single point ground for the ML4769 PWR GND
pin and the input and output capacitors, and connect
the GND pin to PWR GND using a separate trace
Separate the ground for the converter circuitry from the
ground of the load circuitry and connect at a single
point
Route the feedback trace away from the V
L2
trace to
avoid noise pickup
Route the high frequency bypass capacitor from a
V
OUT
location near the output voltage setting resistor
to the GND pin
DESIGN EXAMPLE
In order to design a boost converter using the ML4769,
it is necessary to define the values of a few parameters.
For this example, assume that V
IN
= 3.0V to 3.6V,
V
OUT
= 5.0V, and I
OUT(MAX)
= 250mA.
First, it must be determined whether the ML4769 is
capable of delivering the output current. This is done
using Equation 1:
0
2
I
A
mA
OUT MAX
(
)
.
.
.
=
+
!
"
-
=
3
5
00392 5
0 488
0144
266
5
7
The next step is to select an inductor. As previously
mentioned, the recommended inductance is 10μH. Make
sure that the peak current rating of the inductor is at least
1.0A, and that the DC resistance of the inductor is
between 50m
W
and 100m
W
.
Finally, the value of the output capacitor is determined
using Equation 2:
C
H
V
F
OUT
=
50
.
=
44
10
88
m
m
The closest standard value would be a 100μF capacitor
with an ESR rating of 100m
W
. If such a low ESR value
cannot be found, two 47μF capacitors in parallel could
also be used. Since the 250mA output current requirement
is close to the 266mA maximum, a 10nF capacitor from
V
OUT
to GND is recommended.
Finally, the values of R1 and R2 are calculated using
equation 3. Assuming R2 = 250k
W
:
R
V
k
k
k
1
50
257
.
250
250
236
=
-
=
.
W
W
W
The complete circuit is shown in Figure 8. As mentioned
previously, the use of an input supply bypass capacitor is
strongly recommended.
LAYOUT
(Continued)
相關PDF資料 |
PDF描述 |
|---|---|
| ML4803IP-1 | 8-Pin PFC and PWM Controller Combo |
| ML4803IP-2 | 8-Pin PFC and PWM Controller Combo |
| ML4803CP-1 | 8-Pin PFC and PWM Controller Combo |
| ML4803CP-2 | 8-Pin PFC and PWM Controller Combo |
| ML4803CP-1 | 8-Pin PFC and PWM Controller Combo |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML4769ES UP WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| ML4769ESX | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ML4770 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:2 Cell, Adjustable Output, High Current Boost Regulator with Load Disconnect |
| ML4770CS | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:2 Cell, Adjustable Output, High Current Boost Regulator with Load Disconnect |
| ML4770ES | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:2 Cell, Adjustable Output, High Current Boost Regulator with Load Disconnect |
發布緊急采購，3分鐘左右您將得到回復。