- 您現在的位置：買賣IC網 > PDF目錄377970 > ML4802 (Fairchild Semiconductor Corporation) PFC/PWM Controller Combo with Green Mode(綠色模式PFC/PWM控制器組合芯片) PDF資料下載
參數資料
| 型號： | ML4802 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | PFC/PWM Controller Combo with Green Mode(綠色模式PFC/PWM控制器組合芯片) |
| 中文描述： | 式PFC / PWM控制器組合（綠色模式功率因數校正/脈寬調制控制器組合芯片綠色模式） |
| 文件頁數： | 9/15頁 |
| 文件大小： | 321K |
| 代理商： | ML4802 |
ML4802
August 2000 Datasheet
REV. 1.0 10/10/2000
9
The output of the gain modulator is a current signal, in the
form of a full wave rectified sinusoid at twice the line
frequency. This current is applied to the virtual-ground
(negative) input of the current error amplifier. In this way
the gain modulator forms the reference for the current
error loop, and ultimately controls the instantaneous
current draw of the PFC from the power line. The general
form for the output of the gain modulator is:
given by:
where K is in units of V
-1
.
Note that the output current of the gain modulator is
limited to
500
μ
A.
Current Error Amplifier
The current error amplifier’s output controls the PFC duty
cycle to keep the current through the boost inductor a
linear function of the line voltage. At the inverting input
to the current error amplifier, the output current of the
gain modulator is summed with a current which results
from a negative voltage being impressed upon the ISENSE
pin (current into ISENSE @ VSENSE/1.8k
)
. The negative
voltage on ISENSE represents the sum of all currents
flowing in the PFC circuit, and is typically derived from a
current sense resistor in series with the negative terminal
of the input bridge rectifier. As stated above, the ground.
Given this fact, and the arrangement of the duty cycle
modulator polarities internal to the PFC, an increase in
positive current from the gain modulator will cause the
output stage to increase its duty cycle until the voltage on
ISENSE is adequately negative to cancel this increased
current. Similarly, if the gain modulator’s output
decreases, the output duty cycle will decrease to achieve
a less negative voltage on the ISENSE pin.
There is a modest degree of gain contouring applied to the
transfer characteristic of the current error amplifier, to
increase its speed of response to current-loop
perturbations.
Cycle-By-Cycle Current Limiter
The ISENSE pin, as well as being a part of the current
feedback loop, is a direct input to the cycle-by-cycle
current limiter for the PFC section. Should the input
voltage at this pin ever be more negative than –1.5V, the
output of the PFC will be disabled until the protection
flip-flop is reset by the clock pulse at the start of the next
PFC power cycle.
Overvoltage Protection
The OVP comparator serves to protect the power circuit
from being subjected to excessive voltages if the load
should suddenly change. A resistor divider from the high
voltage DC output of the PFC is fed to VFB. When the
voltage on VFB exceeds 2.75V, the PFC output driver is
shut down. The PWM section will continue to operate. The
OVP comparator has 250mV of hysteresis, and the PFC
will not restart until the voltage at VFB drops below 2.5V.
The VFB should be set at a level where the active and
passive external power components and the ML4802 are
within their safe operating voltages, but not so low as to
interfere with the boost voltage regulation loop.
Error Amplifier Compensation
The PWM loading of the PFC can be modeled as a
negative resistor; an increase in input voltage to the PWM
causes a decrease in the input current. This response
dictates the proper compensation of the two
transconductance error amplifiers. Figure 4 shows the
types of compensation networks most commonly used for
the voltage and current error amplifiers, along with their
respective return points. The current loop compensation is
returned to VREF to produce a soft-start characteristic on
the PFC: as the reference voltage comes up from zero
volts, it creates a differentiated voltage on IEAO which
prevents the PFC from immediately demanding a full duty
cycle on its boost converter. This then works in
conjunction with the low output current of the VEA to
ensure low component stress at PFC startup.
FUNCTIONAL DESCRIPTION
(Continued)
Figure 4. Compensation Network Connections for the
Voltage and Current Error Amplifiers
15
VEAO
IEAO
VFB
IAC
VRMS
ISENSE
2.5V
1.6k
1.6k
-
+
16
2
4
3
VEA
+
–
IEA
+
-
VREF
1
PFC
OUTPUT
GAIN
MODULATOR
More exactly, the output current of the gain modulator is
IGAINMOD =IAC
VEAO
2
VRMS
V
1
IGAINMOD=K
VEAO-0.625V
IAC
相關PDF資料 |
PDF描述 |
|---|---|
| ML4803 | 8-Pin PFC and PWM Controller Combo(八腳PFC/PWM控制器組合芯片) |
| ML4804CP | Power Factor Correction and PWM Controller Combo |
| ML4804CS | Power Factor Correction and PWM Controller Combo |
| ML4804IP | Power Factor Correction and PWM Controller Combo |
| ML4804IS | Power Factor Correction and PWM Controller Combo |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML4802CP | 功能描述:功率因數校正 IC DIP-16 RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| ML4802CS | 功能描述:功率因數校正 IC SOIC-16 RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| ML4802CSX | 功能描述:功率因數校正 IC SOIC-16 RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| ML4802IP | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:PFC/PWM Controller Combo with Green Mode |
| ML4802IS | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:PFC/PWM Controller Combo with Green Mode |
發布緊急采購，3分鐘左右您將得到回復。