- 您現在的位置：買賣IC網 > PDF目錄377970 > ML4833 (Fairchild Semiconductor Corporation) Electronic Dimming Ballast Controller(電子調光整流器控制器) PDF資料下載
參數資料
| 型號： | ML4833 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Electronic Dimming Ballast Controller(電子調光整流器控制器) |
| 中文描述： | 電子調光鎮流器控制器（電子調光整流器控制器） |
| 文件頁數： | 9/13頁 |
| 文件大小： | 136K |
| 代理商： | ML4833 |
ML4833
REV. 1.0 10/12/2000
9
This assumes that t
CHG
>> t
DIS
.
When LFB OUT is high, I
CH
= 0 and the minimum
frequency occurs. The charging current varies according
to two control inputs to the oscillator:
1.
The output of the preheat timer
2.
The voltage at LFB OUT (lamp feedback amplifier
output)
In preheat condition, charging current is fixed at
I
R
CHG PREHEAT
(
SET
)
.
=
2 5
(6)
In running mode, charging current decreases as the
voltage rises from 0V to V
OH
at the LAMP FB amplifier.
The highest frequency will be attained when I
CHG
is
highest, which is attained when voltage at LFB OUT
is at 0V:
I
R
CHG
SET
( )
5
=
(7)
Highest lamp power, and lowest output frequency are
attained when voltage at LFB OUT is at its maximum
output voltage (V
OH
).
In this condition, the minimum operating frequency of the
ballast is set per equation 5 above.
For the IC to be used effectively in dimming ballasts with
higher Q output networks a larger C
T
value and lower R
T
value can be used, to yield a smaller frequency excursion
over the control range (voltage at LFB OUT). The
discharge current is set to 5mA. Assuming that I
DIS
>>
I
RT
:
t
C
DIS VCO
(
T
)
×
600
(8)
IC BIAS, UNDER-VOLTAGE LOCKOUT AND
THERMAL SHUTDOWN
The IC includes a shunt clamp which will limit the
voltage at V
CC
to 15V (V
CCZ
). The IC should be fed with
a current limited source, typically derived from the
ballast transformer auxiliary winding. When V
CC
is below
V
CCZ
– 1.1V, the IC draws less than 0.48mA of quiescent
current and the outputs are off. This allows the IC to start
using a “bleed resistor” from the rectified AC line.
To help reduce ballast cost, the ML4833 includes a
temperature sensor which will inhibit ballast operation if
the IC’s junction temperature exceeds 120°C. In order to
use this sensor in lieu of an external sensor, care should
be taken when placing the IC to ensure that it is sensing
temperature at the physically appropriate point in the
ballast. The ML4833’s die temperature can be estimated
with the following equation:
T
T
P
(
C W
°
/
J
A
D
+
+
)
65
(9)
VCCZ
V(ON)
V(OFF)
5.5mA
0.34mA
V
CC
I
CC
t
t
Figure 7. Typical V
CC
and I
CC
Waveforms when
the ML4833 is Started with a Bleed Resistor from
the Rectified AC Line and Bootstrapped from an
Auxiliary Winding.
STARTING, RE-START, PREHEAT AND INTERRUPT
The lamp starting scenario implemented in the ML4833
is designed to maximize lamp life and minimize ballast
heating during lamp out conditions.
The circuit in Figure 8 controls the lamp starting
scenarios: Filament preheat and lamp out interrupt. C
X
is
charged with a current of I
R(SET)
/4 and discharged through
R
X
. The voltage at C
X
is initialized to 0.7V (V
BE
) at power
up. The time for C
X
to rise to 4.8V is the filament preheat
time. During that time, the oscillator charging current
(I
CHG
) is 2.5/R
SET
. This will produce a high frequency for
filament preheat, but will not produce sufficient voltage
to ignite the lamp or cause significant glow current.
After cathode heating, the inverter frequency drops to F
MIN
causing a high voltage to appear to ignite the lamp. If
lamp current is not detected when the lamp is supposed
to have ignited, the lamp voltage feedback coming into
pin 8 remains below 1.25V, the C
X
charging current is
shut off and the inverter is inhibited until C
X
is discharged
by R
X
to the 1.2V threshold. Shutting off the inverter in
this manner prevents the inverter from generating
excessive heat when the lamp fails to strike or is out of
socket. Typically this time is set to be fairly long by
choosing a large value of R
X
.
相關PDF資料 |
PDF描述 |
|---|---|
| ML4835 | Compact Fluorescent Electronic Dimming Ballast Controller(小型熒光管整流器控制器) |
| ML4836 | Compact Fluorescent Electronic Dimming Ballast Controller(小型熒光管整流器控制器) |
| ML4841 | Variable Feedforward PFC/PWM Controller Combo(前饋可變PFC/PWM控制器組合芯片) |
| ML4851 | Low Current, Voltage Boost Regulator(小電流升壓穩壓器) |
| ML4854IT | Adjustable, Low-Current, 2-Cell Boost Regulator with Shutdown and Low Battery Detect |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML4833CP | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Electronic Dimming Ballast Controller |
| ML4833CS | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Electronic Dimming Ballast Controller |
| ML4835 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Compact Fluorescent Electronic Dimming Ballast Controller |
| ML4835CP | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Compact Fluorescent Electronic Dimming Ballast Controller |
| ML4835CS | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Compact Fluorescent Electronic Dimming Ballast Controller |
發布緊急采購，3分鐘左右您將得到回復。