- 您現在的位置：買賣IC網 > PDF目錄377971 > ML4835 (Fairchild Semiconductor Corporation) Compact Fluorescent Electronic Dimming Ballast Controller(小型熒光管整流器控制器) PDF資料下載
參數資料
| 型號： | ML4835 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Compact Fluorescent Electronic Dimming Ballast Controller(小型熒光管整流器控制器) |
| 中文描述： | 緊湊型熒光燈電子調光鎮流器控制器（小型熒光管整流器控制器） |
| 文件頁數： | 10/17頁 |
| 文件大?。?/td> | 214K |
| 代理商： | ML4835 |
ML4835
10
REV. 1.0 10/12/2000
(C1) in the frequency compensation network. The
compensation network shown in Figure 5 will introduce a
zero and a pole at:
f
R C
f
R C
Z
P
=
=
1
2
1
2
1
2
π
π
(2)
Figure 4 shows the output configuration for the
operational transconductance amplifiers.
A DC path to ground or V
CC
at the output of the
transconductance amplifiers will introduce an offset error.
The magnitude of the offset voltage that will appear at the
input is given by V
OS
= io/gm. For an io of 1μA and a gm
of 0.05 μW the input referred offset will be 20mV.
Capacitor C1 as shown in Figure 5 is used to block the
DC current to minimize the adverse effect of offsets.
Slew rate enhancement is incorporated into all of the
operational transconductance amplifiers in the ML4835.
This improves the recovery of the circuit in response to
power up and transient conditions. The response to large
signals will be somewhat non-linear as the
transconductance amplifiers change from their low to
high transconductance mode, as illustrated in Figure 7.
END OF LAMP LIFE
At the end of a lamp’s life when the emissive material is
depleted, the arc current is rectified and high voltage
occurs across the lamp near the depleted cathode. The
ballast acts as a constant current source so power is
dissipated near the depleted cathode which can lead to
arcing and bulb cracking. Compact fluorescent lamps are
more prone to cracking or shattering because their small
diameter can’t dissipate as much heat as the larger linear
lamps. Compact fluorescents also present more of a
safety hazard since they are usually used in downlighting
systems without reflector covers.
EOL and the ML4835
The ML4835 uses a circuit that creates a DC voltage
representative of the power supplied to the lamps through
the inverter. This voltage is used by the ML4835 to latch
off the ballast when it exceeds an internal threshold. An
external resistor can be used as the “EOL latch resistor” to
set the power level trip point, as shown in by R9 in Figure
12. See Micro Linear ML4835 User Guide and
applications notes for more details. Figure 4 illustrates a
simplified model of ML4835 EOL functionality.
BALLAST OUTPUT SECTION
The IC controls output power to the lamps via frequency
modulation with non-overlapping conduction. This means
that both ballast output drivers will be low during the
discharging time t
DIS
of the oscillator capacitor C
T
.
OSCILLATOR
The VCO frequency ranges are controlled by the output
of the LFB amplifier (R
SET
). As lamp current decreases,
LFB OUT falls in voltage, causing the C
T
charging current
to increase, thereby causing the oscillator frequency to
increase. Since the ballast output network attenuates high
frequencies, the power to the lamp will be decreased. The
oscillator frequency is determined by the following
equations:
F
t
t
OSC
CHG
DIS
=
+
1
(3)
and
t
R C In
V
V
I
R
R
V
V
II
CHG
REF
CHG
T
TL
REF
CHG
T
TH
=
+
+
×
×
F
I
(4)
The oscillator’s minimum frequency is set when I
CHG
= 0
where:
F
R C
MIN
T
×
1
051
.
(5)
The oscillator's start frequency can be expressed by:
F
R R
c
C
START
T
T
=
×
×
1
051
.
2
h
(5a)
Both equations assume that t
CHG
>> t
DIS
.
When LFB OUT is high, I
CHG
= 0 and the minimum
frequency occurs. The charging current varies according
to two control inputs to the oscillator:
1. The output of the preheat timer
2. The voltage at LFB OUT (lamp feedback amplifier
output)
In preheat condition, charging current is fixed at
I
R
CHG PREHEAT
(
SET
)
.
=
25
(6)
In running mode, charging current decreases as the
voltage rises from 0V to V
OH
at the LAMP FB amplifier.
The charging current behavior can be expressed as:
I
V
R
LEAO
k
±
8
CHG
SET
=
5
25%
(7)
The highest frequency is attained when I
CHG
is highest,
which is attained when voltage at LFB OUT is at 0V:
I
R
CHG
SET
( )
5
=
(8)
FUNCTIONAL DESCRIPTION
(Continued)
相關PDF資料 |
PDF描述 |
|---|---|
| ML4836 | Compact Fluorescent Electronic Dimming Ballast Controller(小型熒光管整流器控制器) |
| ML4841 | Variable Feedforward PFC/PWM Controller Combo(前饋可變PFC/PWM控制器組合芯片) |
| ML4851 | Low Current, Voltage Boost Regulator(小電流升壓穩壓器) |
| ML4854IT | Adjustable, Low-Current, 2-Cell Boost Regulator with Shutdown and Low Battery Detect |
| ML4854 | Adjustable, Low-Current, 2-Cell Boost Regulator with Shutdown and Low Battery Detect |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML4835CP | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Compact Fluorescent Electronic Dimming Ballast Controller |
| ML4835CS | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Compact Fluorescent Electronic Dimming Ballast Controller |
| ML4836 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Compact Fluorescent Electronic Dimming Ballast Controller |
| ML4836CP | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Compact Fluorescent Electronic Dimming Ballast Controller |
| ML4836CS | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Compact Fluorescent Electronic Dimming Ballast Controller |
發布緊急采購，3分鐘左右您將得到回復。