- 您現在的位置：買賣IC網 > PDF目錄376180 > MLX10803KDC (Electronic Theatre Controls, Inc.) High power LED driver PDF資料下載
參數資料
| 型號： | MLX10803KDC |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | High power LED driver |
| 中文描述： | 高功率LED驅動器 |
| 文件頁數： | 5/25頁 |
| 文件大?。?/td> | 479K |
| 代理商： | MLX10803KDC |
IC specification
MLX10803
High power LED driver
3901010803 Page 5/25
Data Sheet
Rev 025 2/OCT/07
1.1.3. Principle soft start up LED driver diagram
ROSC
IREF2
VREF
GND
RSENSE
DRVGATE
VS/PWM
VBAT
GND
100nF
Cap for EMC directly
on the connector
100nF...1uF
IREF1
Figure 3:
Application with gradual increase of light intensity after power up (soft start)
1.1.4. LED driver application notes
The MLX10803 is optimised for the use of low cost coils and n-channel MOSFETs. For a standard application with
1 LED and an average current of 350mA, a coil of about 100μH…220μH and
≤
1
DC resistance should be
chosen. The sense resistor should have a value between 0.27
…0.47
/ 250mW.
As a general rule: for higher load current lower inductance of the coil is needed because higher currents lengthen
the charging time of the coil. Thus, switching frequencies may become lower than 20kHz which is often not desired.
It is possible to set the peak current and the average current of the LED by variation of the RSENSE resistor, the
coil value and the internal oscillator frequency (ROCS resistor).
The flyback diode that carries the load current during the passive state (driver OFF) should be a fast switching and
low intrinsic capacitance diode like ES1D or BYG80 in order to avoid parasitic spikes on RSENSE. The diode must
be able to carry the LED current flowing during the OFF time of the driver.
The n-channel MOSFET should have low intrinsic capacitances, a drain-source voltage suitable for the application
and must be able to carry the current flowing through the LED(s) during the ON time. To decrease the time of
transistor switching and to improve the thermal behaviour of the module, the lines between transistor and IC should
be minimised.
For applications that use an NTC resistor for temperature sensing, the NTC value has to be selected according to
the application requirements. For most applications, a NTC value up to 470k
will be suitable.
In case of longer lines between the IC and the coil (which should be avoided because of EMI), a capacitor might be
placed in parallel to RSENSE to avoid crosstalk and parasitic switching. Well chosen parameters for external
components can help to avoid such conditions. The goal should be to unload the coil as much as possible during
the selected off time (see also chapter 7).
To reduce an influence of noise which can be coupled to sensitive reference pins IREF1, IREF2 it is possible to
connect noise-filtering capacitors in parallel to IREF1 and IREF2 resistors (see Figure 1, Cnoise capacitors). The
coupling also should be reduced as much as possible by proper routing of IREF1 and IREF2 stripes on PCB. IREF2
相關PDF資料 |
PDF描述 |
|---|---|
| MLX90110 | 128bit OTP/RW Transponder |
| MLX90111 | 128bit Read Write Transponder |
| MLX90217 | Hall-Effect Cam Sensor |
| MLX90240 | Pressure Sensor IC |
| MLX90242LUA-CC03 | Linear Hall Effect Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MLX10803KDC-AAA-000-RE | 功能描述:IC LED DRVR HP CONST CURR 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:1 系列:- 恒定電流:- 恒定電壓:- 拓撲:PWM，切換式電容器（充電泵） 輸出數:1 內部驅動器:是 類型 - 主要:背光 類型 - 次要:白色 LED 頻率:642kHz 電源電壓:2.7 V ~ 5.5 V 輸出電壓:5V 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-VSON 包裝:剪切帶 (CT) 工作溫度:-30°C ~ 85°C 產品目錄頁面:1371 (CN2011-ZH PDF) 其它名稱:BD1603NUV-E2CT |
| MLX10803KDC-AAA-000-TU | 制造商:Melexis Semiconductors 功能描述:IC LED DRIVER HP 8SOIC |
| MLX10803KDC-TR-7 | 制造商:Melexis Semiconductors 功能描述: |
| MLX12101 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Sensor Protection IC |
| MLX12101E | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Sensor Protection IC |
發布緊急采購，3分鐘左右您將得到回復。