參數資料
型號: MLX90316EDC-SPI
廠商: Electronic Theatre Controls, Inc.
英文描述: Rotary Position Sensor IC
中文描述: 旋轉位置傳感器IC
文件頁數: 20/41頁
文件大小: 688K
代理商: MLX90316EDC-SPI
MLX90316
Rotary Position Sensor IC
3901090316
Rev. 003
Page 20 of 41
Data Sheet
April 07
14.4. Sensor Front-End
Parameter
Value
Unit
HIGHSPEED
0 = Slow mode
1 = Fast mode
0 = disable
1 = enable
0 = disable
1 = enable
0
15
0
15
0
15
ARGC
AUTO_RG
RoughGain
RGThresL
RGThresH
14.4.1. HIGHSPEED Parameter
The HIGHSPEED parameter defines the main frequency for the DSP.
HIGHSPEED = 0 selects the Slow mode with a 7 MHz master clock.
HIGHSPEED = 1 selects the Fast mode with a 20 MHz master clock.
For better noise performance, the Slow Mode must be enabled.
14.4.2. ARGC, AUTO_RG, RoughGain Parameters
AUTO_RG and ARGC parameters enable the automatic gain control (AGC) of the analog chain. The AGC
loop is based on
(V
X
)2+ (V
Y
)2 = (Amplitude)2 = (Radius)2
and it targets an amplitude of 90% of the ADC input span.
At Start-Up phase, the gain stored in the parameter RoughGain is always used. Depending of the
AUTO_RG and ARGC settings, the AGC regulation acts as follow:
If ARGC is set, the regulation proceeds by jump to reach the target gain. Note that this regulation
is only valid if the starting gain does not saturate the ADC. Melexis recommendation is to use
RoughGain
3 if ARGC=1.
If ARGC is “0” and AUTO_RG is set to “1”, the regulation adapts every cycle by one gain code the
current gain to reach the 90% ADC span target. Note that if the value of RoughGain is too far
from the actual gain, the chip will enter the normal operating mode (after the Start-Up phase) with
an incorrect gain which will cause the device to go in diagnostic low (field too low/field too high –
See section 15).
If ARGC and AUTO_RG are “0”, the AGC regulation is off and the gain used is the value stored in
the parameter RoughGain. Melexis does not advise the use of this mode.
The parameter AUTO_RG activates the automatic regulation during normal operation of the device as
background task.
Melexis strongly recommend to set ARGC = “1”, AUTO_RG = “1” and RoughGain
3 for all types of
application. If the magnetic specifications of the application are well known and under control, the
appropriate RoughGain can also be programmed with ARGC set to “0” and AUTO_RG to “1”.
Please note that the angular errors listed in the section 10 are only valid if the AUTO_RG is activated.
AUTO_RG avoids also the saturation of the analog chain and the associated linearity error.
The current gain (RG) can be read out with the PTC-04 and gives a rough indication of the applied
magnetic flux density (Amplitude).
相關PDF資料
PDF描述
MLX90316KDC-PPA Rotary Position Sensor IC
MLX90316KDC-SPI Rotary Position Sensor IC
MMBL4148H 4500 GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN
MMBL914H SURFACE MOUNT SWITCHING DIODE
MMBT2907A Small Signal Transistors(PNP)(小信號晶體管(PNP))
相關代理商/技術參數
參數描述
MLX90316EGO 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Rotary Position Sensor IC
MLX90316EGO-BCG-000-RE 功能描述:IC SENSOR ROTARY POSITION16TSSOP RoHS:是 類別:傳感器,轉換器 >> 磁性 - 霍爾效應,數字式開關,線性,羅盤 (IC) 系列:Triaxis™ 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出(最大):- 輸出類型:數字式,PWM,8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP(0.209",5.30mm 寬) 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR
MLX90316EGO-BCG-000-TU 制造商:Melexis Semiconductors 功能描述:IC SENSOR INTERFACE ROT 16TSSOP 制造商:Melexis Semiconductors 功能描述:MLX90316 Series 360 /s 4.5 to 5.5 V SMT Rotary Position Sensor IC - TSSOP-16
MLX90316EGO-BDG-100-RE 制造商:Melexis Semiconductors 功能描述:IC SENSOR INTERFACE ROT 16TSSOP
MLX90316EGO-BDG-100-TU 制造商:Melexis Semiconductors 功能描述:IC SENSOR INTERFACE ROT 16TSSOP 制造商:Melexis Semiconductors 功能描述:MLX90316 Series 360 /s 4.5 to 5.5 V SMT Rotary Position Sensor IC - TSSOP-16