- 您現在的位置：買賣IC網 > PDF目錄385628 > MMSF3P03HD (ON SEMICONDUCTOR) Power MOSFET 3 Amps, 30 Volts P-Channel(3A，30V，P溝道增強型功率MOS場效應管) PDF資料下載
參數資料
| 型號： | MMSF3P03HD |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Power MOSFET 3 Amps, 30 Volts P-Channel(3A，30V，P溝道增強型功率MOS場效應管) |
| 中文描述： | 功率MOSFET 3安培，30伏特P溝道條第（3A，30V的，P溝道增強型功率馬鞍山場效應管） |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 132K |
| 代理商： | MMSF3P03HD |
MMSF3P03HD
http://onsemi.com
9
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of
control settings that will give the desired heat pattern. The
operator must set temperatures for several heating zones
and a figure for belt speed. Taken together, these control
settings make up a heating “profile” for that particular
circuit board. On machines controlled by a computer, the
computer remembers these profiles from one operating
session to the next. Figure 16 shows a typical heating
profile for use when soldering a surface mount device to a
printed circuit board. This profile will vary among
soldering systems, but it is a good starting point. Factors
that can affect the profile include the type of soldering
system in use, density and types of components on the
board, type of solder used, and the type of board or
substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density
board. The Vitronics SMD310 convection/infrared reflow
soldering system was used to generate this profile. The type
of solder used was 62/36/2 Tin Lead Silver with a melting
point between 177–189
°
C. When this type of furnace is
used for solder reflow work, the circuit boards and solder
joints tend to heat first. The components on the board are
then heated by conduction. The circuit board, because it has
a large surface area, absorbs the thermal energy more
efficiently, then distributes this energy to the components.
Because of this effect, the main body of a component may
be up to 30 degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
5
°
C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO 219
°
C
PEAK AT
SOLDER
JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
170
°
C
140
°
C
Figure 16. Typical Solder Heating Profile
相關PDF資料 |
PDF描述 |
|---|---|
| MMSF7P03HD | Power MOSFET 7 A, 30 V, P Channel SO8(7A，30V，P溝道功率MOSFET) |
| MMSZ15T3 | Zener Voltage Regulators 500 mW SOD123 Surface Mount(500mW，SOD123，表面安裝齊納穩壓管) |
| MMSZ10T3 | Zener Voltage Regulators 500 mW SOD123 Surface Mount(500mW，SOD123，表面安裝齊納穩壓管) |
| MMSZ13T3 | Zener Voltage Regulators 500 mW SOD123 Surface Mount(500mW，SOD123，表面安裝齊納穩壓管) |
| MMSZ9V1T1 | Zener Voltage Regulators 500 mW SOD123 Surface Mount(500mW，SOD123，表面安裝齊納穩壓管) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MMSF4205R2 | 制造商:ON Semiconductor 功能描述:Trans MOSFET P-CH 20V 10A 8-Pin SOIC T/R |
| MMSF4N01HD | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:TMOS MOSFET 5.8 AMPERES 20 VOLTS |
| MMSF4N01HDR2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述: |
| MMSF4P01HD | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:SINGLE TMOS POWER FET 4.0 AMPERES 12 VOLTS |
| MMSF5N02HD | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:SINGLE TMOS POWER MOSFET 5.0 AMPERES 20 VOLTS |
發布緊急采購，3分鐘左右您將得到回復。