參數資料
型號： MPC5554MVR112R2
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, PBGA416
封裝： 27 X 27 MM, 1 MM PITCH, LEAD FREE, PLASTIC, MS-034AAL-1, TEPBGA-416
文件頁數： 4/58頁
文件大?。?/td> 1452K
代理商： MPC5554MVR112R2
MPC5554 Microcontroller Data Sheet, Rev. 2.0
Electrical Characteristics
Freescale Semiconductor
12
To avoid this condition, minimize the ramp time of the VDD supply to a time period less than the time
required to enable the external circuitry connected to the device outputs.
3.7.1
Input Value of Pins During POR Dependent on VDD33
When powering up the device, VDD33 must not lag the latest VDDSYN or RESET power pin (VDDEH6) by
more than the VDD33 lag specification listed in Table 6, spec 8. This avoids accidentally selecting the
bypass clock mode because the internal versions of PLLCFG[0:1] and RSTCFG are not powered and
therefore cannot read the default state when POR negates. VDD33 can lag VDDSYN or the RESET power
pin (VDDEH6), but cannot lag both by more than the VDD33 lag specification. This VDD33 lag specification
applies during power up only. VDD33 has no lead or lag requirements when powering down.
3.7.2
Power-Up Sequence (VRC33 Grounded)
The 1.5 V VDD power supply must rise to 1.35 V before the 3.3 V VDDSYN power supply and the RESET
power supply rises above 2.0 V. This ensures that digital logic in the PLL for the 1.5 V power supply does
not begin to operate below the specified operation range lower limit of 1.35 V. Because the internal 1.5 V
POR is disabled, the internal 3.3 V POR or the RESET power POR must hold the device in reset. Since
they can negate as low as 2.0 V, VDD must be within specification before the 3.3 V POR and the RESET
POR negate.
Figure 2. Power-Up Sequence (VRC33 Grounded)
3.7.3
Power-Down Sequence (VRC33 Grounded)
The only requirement for the power-down sequence when VRC33 is grounded is that if VDD decreases to
less than its operating range, VDDSYN or the RESET power must decrease to less than 2.0 V before the
VDD power is allowed to increase to its operating range. This ensures that the digital 1.5 V logic, which is
reset by the ORed POR only and can cause the 1.5 V supply to decrease below its specification, is reset
properly.
VDDSYN and RESET Power
VDD
2.0 V
1.35 V
VDD must reach 1.35 V before VDDSYN and the RESET power reach 2.0 V
相關PDF資料
PDF描述
MPC5554AVR132R2 MICROCONTROLLER, PBGA416
MPC5554MZP80R2 32-BIT, FLASH, 80 MHz, MICROCONTROLLER, PBGA416
MPC5554AVR132 32-BIT, FLASH, 132 MHz, MICROCONTROLLER, PBGA416
MPC5554MVR112 32-BIT, FLASH, 112 MHz, MICROCONTROLLER, PBGA416
MPC5554MZP132R2 32-BIT, FLASH, 132 MHz, MICROCONTROLLER, PBGA416
相關代理商/技術參數
參數描述
MPC5554MVR132 功能描述:32位微控制器 - MCU MPC5554 COPPERHEAD Qorivva RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
MPC5554MVR132R2 功能描述:32位微控制器 - MCU COPPERHEAD Qorivva RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
MPC5554MVR80 制造商:Freescale Semiconductor 功能描述:MCU 32BIT 55XX RISC 2MB FLASH 1.8V/2.5V/3.3V/5V 416BGA - Trays
MPC5554MVR80R2 制造商:Freescale Semiconductor 功能描述:MCU 32BIT 55XX RISC 2MB FLASH 1.8V/2.5V/3.3V/5V 416BGA - Tape and Reel
MPC5554MZP112 制造商:Freescale Semiconductor 功能描述:MCU 32BIT 55XX RISC 2MB FLASH 1.8V/2.5V/3.3V/5V 416BGA - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*