- 您現在的位置：買賣IC網 > PDF目錄9014 > MPC9239ACR2 (IDT, Integrated Device Technology Inc)IC CLK SYNTH LV PECL 32-LQFP PDF資料下載
參數資料
| 型號： | MPC9239ACR2 |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 9/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLK SYNTH LV PECL 32-LQFP |
| 標準包裝： | 2,000 |
| 類型： | 時鐘/頻率合成器 |
| PLL： | 是 |
| 輸入： | 晶體 |
| 輸出： | LVPECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:1 |
| 差分 - 輸入:輸出： | 無/是 |
| 頻率 - 最大： | 900MHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-LQFP |
| 供應商設備封裝： | 32-TQFP（7x7） |
| 包裝： | 帶卷 (TR) |
MPC9239
REVISION 2
DECEMBER 18, 2012
8
2012 Integrated Device Technology, Inc.
MPC9239 Data Sheet
900 MHz Low Voltage LVPECL Clock Synthesizer
Figure 4. Serial Interface Timing Diagram
Power Supply Filtering
The MPC9239 is a mixed analog/digital product. Its analog
circuitry is naturally susceptible to random noise, especially if
this noise is seen on the power supply pins. Random noise on
the VCC_PLL pin impacts the device characteristics. The
MPC9239 provides separate power supplies for the digital
circuitry (VCC) and the internal PLL (VCC_PLL) of the device. The
purpose of this design technique is to try and isolate the high
switching noise digital outputs from the relatively sensitive
internal analog phase-locked loop. In a controlled environment
such as an evaluation board, this level of isolation is sufficient.
However, in a digital system environment where it is more
difficult to minimize noise on the power supplies a second level
of isolation may be required. The simplest form of isolation is a
power supply filter on the VCC_PLL pin for the MPC9239.
Figure 5 illustrates a typical power supply filter scheme. The
MPC9239 is most susceptible to noise with spectral content in
the 1 kHz to 1 MHz range. Therefore, the filter should be
designed to target this range. The key parameter that needs to
be met in the final filter design is the DC voltage drop that will
be seen between the VCC supply and the MPC9239 pin of the
MPC9239. From the data sheet, the VCC_PLLcurrent (the
current sourced through the VCC_PLL pin) is maximum 20 mA,
assuming that a minimum of 2.835 V must be maintained on the
resistance of 10-15
to meet the voltage drop criteria. The RC
filter pictured will provide a broadband filter with approximately
100:1 attenuation for noise whose spectral content is above
20 kHz. As the noise frequency crosses the series resonant
point of an individual capacitor its overall impedance begins to
look inductive and thus increases with increasing frequency.
The parallel capacitor combination shown ensures that a low
impedance path to ground exists for frequencies well above the
bandwidth of the PLL. Generally, the resistor/capacitor filter will
be cheaper, easier to implement and provide an adequate level
of supply filtering. A higher level of attenuation can be achieved
by replacing the resistor with an appropriate valued inductor. A
1000
H choke will show a significant impedance at 10 kHz
frequencies and above. Because of the current draw and the
voltage that must be maintained on the VCC_PLL pin, a low DC
resistance inductor is required (less than 15
).
Figure 5. VCC_PLL Power Supply Filter
Table 10. Test and Debug Configuration for TEST
T[2:0]
TEST Output
T2
T1
T0
0
12-bit shift register out1
1. Clocked out at the rate of S_CLOCK.
0
1
Logic 1
0
1
0
fXTAL 2
0
1
M-Counter out
1
0
fOUT
1
0
1
Logic 0
1
0
M-Counter out in PLL-bypass mode
1
fOUT 4
Table 11. Debug Configuration for PLL Bypass1
1. T[2:0] = 110. AC specifications do not apply in PLL bypass mode.
Output
Configuration
fOUT
S_CLOCK
N
TEST
M-Counter out2
2. Clocked out at the rate of S_CLOCK
(2 N)
S_CLOCK
S_DATA
S_LOAD
M[6:0]
N[1:0]
P_LOAD
T2
T1
T0
N1
N0
M6
M5
M4
M3
M2
M1
M0
M, N
First
Bit
Last
Bit
VCC_PLL
VCC
MPC9239
C1, C2 = 0.01...0.1 F
VCC
CF = 22 F
RF = 10-15
C2
C1
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B7Y-MX-F1 | CONVERTER MOD DC/DC 3.3V 49.5W |
| VI-B7Y-MW-F3 | CONVERTER MOD DC/DC 3.3V 66W |
| VI-B7Y-MW-F2 | CONVERTER MOD DC/DC 3.3V 66W |
| D38999/24JC4SN | CONN RCPT 4POS JAM NUT W/SCKT |
| MS3454L14S-6S | CONN RCPT 6POS JAM NUT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC9239EI | 功能描述:時鐘合成器/抖動清除器 FSL 900MHz LVPECL Freq. Synthesizer RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MPC9239EIR2 | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MPC9239FA | 功能描述:時鐘合成器/抖動清除器 3.3V 900MHz Clock Generator RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MPC9239FN | 功能描述:IC PECL CLOCK LV 900MHZ 28-PLCC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| MPC9239FNR2 | 功能描述:時鐘合成器/抖動清除器 FSL 900MHz LVPECL Freq. Synthesizer RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。