- 您現在的位置：買賣IC網 > PDF目錄9719 > MPR083Q (Freescale Semiconductor)IC CTLR TOUCH SENSOR PROX 16-QFN PDF資料下載
參數資料
| 型號： | MPR083Q |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 34/35頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTLR TOUCH SENSOR PROX 16-QFN |
| 產品培訓模塊： | Sensor Toolbox |
| 產品目錄繪圖： | MPR08(3,4)Q Top |
| 標準包裝： | 490 |
| 類型： | 電容性 |
| 輸入數/鍵： | 8 個滑塊 |
| 評估套件： | 可供 |
| 數據接口： | I²C，串行 |
| 電源電壓： | 1.8 V ~ 3.6 V |
| 電流 - 電源： | 1.62mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-VQFN 裸露焊盤 |
| 供應商設備封裝： | 16-QFN-EP（5x5） |
| 包裝： | 散裝 |
| 產品目錄頁面： | 2808 (CN2011-ZH PDF) |
| 配用： | DEMOMPR083-ND - BOARD DEMO FOR MPR083 CTLR KITMPR083EVM-ND - KIT EVAL 8POSITION ROTARY TOUCH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁
MPR083
Sensors
8
Freescale Semiconductor
When performing read-after-write verification, remember to re-set the command byte’s address because the stored command
byte address will generally have been auto-incremented after the write (Section 2.4).
Figure 12. ‘n’ Data Bytes Received
2.3.8
Operation with Multiple Master
The application should use repeated starts to address the MPR083 to avoid bus confusion between I2C masters.On a I2C bus,
once a master issues a start/repeated start condition, that master owns the bus until a stop condition occurs. If a master that does
not own the bus attempts to take control of that bus, then improper addressing may occur. An address may always be rewritten
to fix this problem. Follow I2C protocol for multiple master configurations.
2.3.9
Device Reset
The RST is an active-low software reset. This is implemented in the Configuration Register by activating the RST bit. When
asserted, the device clears any transaction to or from the MPR083 on the serial interface and configures the internal registers to
the same state as a power-up reset (Table 4). The MPR083 then waits for a START condition on the serial interface.
The sensor controller is capable of operating down to 1.8 V, however, in order for the sensor controller to exit reset and startup
correctly the host system must initially provide 2.0 V to 3.6 V input to VDD and then follow the process in Figure 13. This process
is required in applications that require regulated operation in the 1.8 V to 2.0 V range. In the case that the application uses an
unregulated battery, then the battery must initially provide at least 2.0 V to correctly power-up the sensor controller which limits
battery selection to the 2.0 V to 3.6 V range.
Figure 13. Low Voltage (1.8 V - 2.0 V) Power-up Sequence
SAAA P
1
SLAVE ADDRESS
COMMAND BYTE
DATA BYTE
acknowledge from MPR083
R/W
nbytes
auto-increment memory
word address
D15 D14 D13 D12 D11 D10 D9 D8
D1 D0
D3 D2
D5 D4
D7 D6
Howcommand byte and data byte
map into MPR083's registers
acknowledge from
MPR083
acknowledge from
MPR083
Established Comms with
Sensor Controller?
i.e. Read from FIFO
Is Data valid? (0 x 40)
Idle Delay Loop
Apply 2.0V to VDD Max
To Sensor Controller
Lower VDD to the desired operating voltage
1.8 V to 2.0 V
False
True
相關PDF資料 |
PDF描述 |
|---|---|
| VE-243-IW-B1 | CONVERTER MOD DC/DC 24V 100W |
| VE-JWF-MX-F1 | CONVERTER MOD DC/DC 72V 75W |
| VE-242-IW-B1 | CONVERTER MOD DC/DC 15V 100W |
| VE-JWD-MX-F4 | CONVERTER MOD DC/DC 85V 75W |
| VE-241-IW-B1 | CONVERTER MOD DC/DC 12V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPR083QR2 | 功能描述:電容觸摸傳感器 10 PADS 8 POSITION RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| MPR084 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller |
| MPR084EJ | 功能描述:電容觸摸傳感器 8 POSIT 10 PADS RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| MPR084EJR2 | 功能描述:電容觸摸傳感器 8 POSIT 10 PADS RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| MPR084Q | 功能描述:電容觸摸傳感器 4 POSITION ROTARY & RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
發布緊急采購，3分鐘左右您將得到回復。