- 您現在的位置：買賣IC網 > PDF目錄9725 > MPR084EJ (Freescale Semiconductor)IC CTLR TOUCH SENSR PROX 16TSSOP PDF資料下載
參數資料
| 型號： | MPR084EJ |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 7/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTLR TOUCH SENSR PROX 16TSSOP |
| 產品目錄繪圖： | MPR08(3,4)EJ Top MPR08(3,4)EJ Side |
| 標準包裝： | 96 |
| 類型： | 電容性 |
| 輸入數/鍵： | 8 鍵 |
| 評估套件： | 可供 |
| 數據接口： | I²C，串行 |
| 電源電壓： | 1.8 V ~ 3.6 V |
| 電流 - 電源： | 1.62mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 2808 (CN2011-ZH PDF) |
| 配用： | KITMPR084EVM-ND - KIT EVAL 8-PAD TOUCH MPR084 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
MPR084
Sensors
Freescale Semiconductor
15
4.3
Run1 Mode
When in Run1 mode the sensor controller will run continuously. During Run1 all the modules are synchronized by the Master Tick
Period. This value can be set by using the Master Tick Period Register as outlined in the following section.
While in this mode all functionality of the MPR084 is enabled; touch detection will occur, and I2C communication will be available.
This mode is enabled by setting the Configuration Register’s RUNE and DCE bits high.
4.3.1
Master Tick Period Register
The Master Tick Period Register is used to set the master tick of this system. All parts of the system are synchronized to this
counter. This register is overridden in all modes except for Run1. When not in Run1 mode, the value of this register is ignored
and 8ms is used for the primary clock. The I2C slave address of the Master Tick Period Register is 0x0E.
Figure 18. Master Tick Period Register
4.4
Run2 Mode
When in Run2 mode the sensor controller will continue to scan the electrodes but a low power state will be enabled between
each cycle. Because of this, any I2C communication that occurs, may or may not respond while the sensor is in this mode
If DCE is enabled the sensor controller transitions between low power and active states. During the active part of the cycle
communication with the sensor controller is possible; however, Freescale always requires users to issue an ATTN signal prior to
initiating communications. Accessing the I2C interface while DCE mode is enabled without sending an ATTN signal first is likely
to produce invalid data.
This mode is enabled by setting the Configuration Register’s RUNE bit high and DCE bit low. The only way to exit this mode is
to toggle the Attention Pin, refer to Section 4.7.
4.5
Stop1 Mode
When in Stop1 mode the sensor controller will not scan the electrodes. While capacitance sensing is disabled I2C
communications will still be accepted and the sensor controller will maintain instantaneous response to all register requests. This
is the only mode in which register values can be set.
This mode is enabled by setting the Configuration Register’s RUNE bit low and DCE bit high.
4.6
Stop2 Mode
When in Stop2 mode the sensor controller will not scan the electrodes or accept I2C communication. The MPR084 is off during
this mode.
This mode is enabled by setting the Configuration Register’s RUNE bit low and DCE bit low. The only way to exit this mode is to
toggle the Attention Pin, refer to Section 4.7.
7
6
543210
R
MTP
W
Reset:
0
000101
= Unimplemented
Table 10. Master Tick Period Register Field Descriptions
Field
Description
7:0
MTP
Master Tick Period – The Master Tick Period selects or reports the current value of the
touch sensor controller’s primary clock. The resulting period must be in the range 5ms
to 31ms. If the value is outside of this range the MTP will be set to 00011010.
00000000 Encoding 0 – Sets the primary clock multiplier to 5
~
00011010 Encoding 26 - Sets the primary clock multiplier to 31
相關PDF資料 |
PDF描述 |
|---|---|
| MS27496E9F35S | CONN RCPT 6POS BOX MNT W/SCKT |
| VE-JWL-MX-F4 | CONVERTER MOD DC/DC 28V 75W |
| MS27467E13B35PD | CONN PLUG 22POS STRAIGHT W/PINS |
| MS27473T18A32PD | CONN PLUG 32POS STRAIGHT W/PINS |
| VE-JWL-MX-F2 | CONVERTER MOD DC/DC 28V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPR084EJR2 | 功能描述:電容觸摸傳感器 8 POSIT 10 PADS RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| MPR084Q | 功能描述:電容觸摸傳感器 4 POSITION ROTARY & RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| MPR084QR2 | 功能描述:電容觸摸傳感器 4 POSITION ROTARY & RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| MPR0854FPXXXZ01A | 功能描述:AC/DC CONVERTER 54V 800W 制造商:ge critical power 系列:MPR，耐火 零件狀態:有效 類型:前端 輸出數:1 電壓 - 輸入:90 ~ 264 VAC 電壓 - 輸出 1:54V 電壓 - 輸出 2:- 電壓 - 輸出 3:- 電壓 - 輸出 4:- 電流 - 輸出（最大值）:14.8A 功率（W）:800W 應用:ITE（商業） 電壓 - 隔離:3kV（3000V） 效率:88% 工作溫度:-10°C ~ 70°C（有降額） 特性:熱插拔，I2C? 接口，負載均分，PFC，PMBus?，遠程開/關，遙測，待機輸出，通用輸入 安裝類型:機架安裝 大小/尺寸:8.93" 長 x 3.40" 寬 x 1.57" 高（226.8mm x 86.4mm x 39.9mm） 所需最小負載:無 認可:- 功率（W） - 最大值:800W 標準包裝:5 |
| MPR106M2 | 制造商:DEARBORN ELECTRONICS INC 功能描述:CAPACITOR MILITARY FILM |
發布緊急采購，3分鐘左右您將得到回復。