- 您現在的位置：買賣IC網 > PDF目錄9719 > MPR084Q (Freescale Semiconductor)IC CTLR TOUCH SENSOR PROX 16-QFN PDF資料下載
參數資料
| 型號： | MPR084Q |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 2/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTLR TOUCH SENSOR PROX 16-QFN |
| 產品目錄繪圖： | MPR08(3,4)Q Top |
| 標準包裝： | 490 |
| 類型： | 電容性 |
| 輸入數/鍵： | 8 鍵 |
| 評估套件： | 可供 |
| 數據接口： | I²C，串行 |
| 電源電壓： | 1.8 V ~ 3.6 V |
| 電流 - 電源： | 1.62mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-VQFN 裸露焊盤 |
| 供應商設備封裝： | 16-QFN-EP（5x5） |
| 包裝： | 散裝 |
| 產品目錄頁面： | 2808 (CN2011-ZH PDF) |
| 配用： | KITMPR084EVM-ND - KIT EVAL 8-PAD TOUCH MPR084 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
MPR084
Sensors
10
Freescale Semiconductor
3
Touch Detection
3.1
Introduction
When using a capacitive touch sensor system the raw data must be filtered and interpreted. This process can be done many
different ways but the method used in the MPR084 is explained in this chapter.
3.2
Understanding the Basics
The touch pad interface has to distinguish touch status through varying user conditions (different finger sizes in bare hands or
gloves) and environmental conditions (electrical and RF noise, sensor contamination with dirt or moisture).
The touch pad circuitry reports touch status as one of the following two conditions:
1.
Touch Pad untouched
2.
Touch Pad touched on one of eight pads.
The touch pad is only touched in one position, ideally near the middle of one of the eight pads. If a touch occurs between pads,
untouched will be reported.
3.3
Conditional Output Scenarios
Since it is unlikely that in a real world case a single independent touch will occur two specific multi-touch response cases are
outlined. Methods for changing the sensitivity of the device will be discussed in another Chapter, but the important part is that the
sensitivity is determined by the strength of an input signal. If more than one input signal is above the selected sensitivity then the
touch sensor controller interprets this in a specific way. This functionality is broken down into two different cases.
3.3.1
Simultaneous Touches
Any time multiple touches are detected at the same time the touch sensor controller recognizes this case and accounts for it. The
number of allowed reported touches is settable using the Maximum Number of Touched Positions Register (Section 3.6). In the
case where this register is set to 1, all touches past the first will be ignored and unreported.
A special case is when exact 2 keys are involved in the interaction. In most cases one of the two electrodes will receive a stronger
signal than the other. If the difference in capacitance is statistically significant between the pad with the stronger signal will be
reported
This functionality is sometimes called 1-Keyed Lockout. by changing the Maximum Number of Touched Positions Register
(Section 3.6). this value can be set. Thus the n-key lockout is determined by this register.
3.3.2
Sequential Touches
Another case is when one touch pad is touched and held and a second touch pad is then touched and held. For this situation the
second touch will be ignored and the first touch will continue to be reported.
If the second touch is released before the first touch then the second touch will be completely ignored. But, if the first touch is
released before the second then the system will report that the first key is released and that the second key is now touched. This
functionality is sometimes called 2-Key Rollover.
3.4
Touch Pad Configuration Register
The Touch Pad Configuration Register configures a variety of the MPR084 features. Each of these features is described in
following sections. The I2C slave address of the Touch Pad Configuration Register is 0x03.
Figure 14. Touch Pad Configuration Register
7
6
543210
R
TPSE
0
BKA
ACE
TPRBE
TPTBE
0
TPE
W
Reset:
1
0
000001
= Unimplemented
相關PDF資料 |
PDF描述 |
|---|---|
| VE-24J-IW-B1 | CONVERTER MOD DC/DC 36V 100W |
| MPR083Q | IC CTLR TOUCH SENSOR PROX 16-QFN |
| VE-243-IW-B1 | CONVERTER MOD DC/DC 24V 100W |
| VE-JWF-MX-F1 | CONVERTER MOD DC/DC 72V 75W |
| VE-242-IW-B1 | CONVERTER MOD DC/DC 15V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPR084QR2 | 功能描述:電容觸摸傳感器 4 POSITION ROTARY & RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| MPR0854FPXXXZ01A | 功能描述:AC/DC CONVERTER 54V 800W 制造商:ge critical power 系列:MPR，耐火 零件狀態:有效 類型:前端 輸出數:1 電壓 - 輸入:90 ~ 264 VAC 電壓 - 輸出 1:54V 電壓 - 輸出 2:- 電壓 - 輸出 3:- 電壓 - 輸出 4:- 電流 - 輸出（最大值）:14.8A 功率（W）:800W 應用:ITE（商業） 電壓 - 隔離:3kV（3000V） 效率:88% 工作溫度:-10°C ~ 70°C（有降額） 特性:熱插拔，I2C? 接口，負載均分，PFC，PMBus?，遠程開/關，遙測，待機輸出，通用輸入 安裝類型:機架安裝 大小/尺寸:8.93" 長 x 3.40" 寬 x 1.57" 高（226.8mm x 86.4mm x 39.9mm） 所需最小負載:無 認可:- 功率（W） - 最大值:800W 標準包裝:5 |
| MPR106M2 | 制造商:DEARBORN ELECTRONICS INC 功能描述:CAPACITOR MILITARY FILM |
| MPR106M2S1 | 制造商:SPEC 功能描述: 制造商:Vishay Sprague 功能描述: |
| MPR10JB50L0 | 制造商:SEI Stackpole Electronics Inc 功能描述:- Bulk 制造商:SEI Stackpole Electronics Inc 功能描述:MPR10JB50L0 |
發布緊急采購，3分鐘左右您將得到回復。