- 您現在的位置：買賣IC網 > PDF目錄359201 > MPXM2102AST1 (飛思卡爾半導體(中國)有限公司) 100kPa On-Chip Temperature Compensated & Calibrated Silicon Pressure Sensors(100kPa片內溫度補償和校準硅壓力傳感器) PDF資料下載
參數資料
| 型號： | MPXM2102AST1 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 100kPa On-Chip Temperature Compensated & Calibrated Silicon Pressure Sensors(100kPa片內溫度補償和校準硅壓力傳感器) |
| 中文描述： | 100kPa片上溫度補償 |
| 文件頁數： | 3/8頁 |
| 文件大小： | 127K |
| 代理商： | MPXM2102AST1 |
3
Motorola Sensor Device Data
LINEARITY
Linearity refers to how well a transducer’s output follows
the equation: V
out
= V
off
+ sensitivity x P over the operating
pressure range. There are two basic methods for calculating
nonlinearity: (1) end point straight line fit (see Figure 2) or (2)
a least squares best line fit. While a least squares fit gives
the “best case” linearity error (lower numerical value), the
calculations required are burdensome.
Conversely, an end point fit will give the “worst case” error
(often more desirable in error budget calculations) and the cal-
culations are more straightforward for the user. Motorola’s
specified pressure sensor linearities are based on the end
point straight line method measured at the midrange pressure.
Figure 2. Linearity Specification Comparison
&'
&$(%
)'"!
%
#%&&(% (&
! #"!'
&'%' ! '
+%'
#%"% !
(%)
&' &$(%& '
&'%' !
)'"!
"&'
ON–CHIP TEMPERATURE COMPENSATION and CALIBRATION
Figure 3 shows the minimum, maximum and typical output
characteristics of the MPXM2102 series at 25
°
C. The output
is directly proportional to the differential pressure and is es-
sentially a straight line.
A silicone gel isolates the die surface and wire bonds from
the environment, while allowing the pressure signal to be
transmitted to the silicon diaphragm.
Figure 3. Output versus Pressure Differential
"
2#-
#&
9
&#!
%!
',#
"&'
',#
',#
!
)
&
)0/
'
# #
°
+
ORDERING INFORMATION
Device Type
Options
Case Type
MPXM2102D
Non–ported
1320
MPXM2102DT1
Non–ported, Tape and Reel
1320
MPXM2102GS
Ported
1320A
MPXM2102GST1
Ported, Tape and Reel
1320A
MPXM2102A
Non–ported
1320
MPXM2102AT1
Non–ported, Tape and Reel
1320
MPXM2102AS
Ported
1320A
MPXM2102AST1
Ported, Tape and Reel
1320A
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MPXM2102G | 100 kPa On-Chip Temperature Compensated & Calibrated Silicon Pressure Sensors |
| MPXM2202A | 200kPa On-Chip Temperature Compensated & Calibrated Silicon Pressure Sensors(200kPa片內溫度補償和校準硅壓力傳感器) |
| MPXM2202G | 200 kPa On-Chip Temperature Compensated and Calibrated Silicon Pressure Sensors |
| MPXV10G | 10 kPa Uncompensated Silicon Pressure Sensors |
| MPXV2010G | 10 kPa On-Chip Temperature Compensated & Calibrated Silicon Pressure Sensors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPXM2102AT1 | 功能描述:板上安裝壓力/力傳感器 FINISH GOOD RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPXM2102D | 功能描述:板上安裝壓力/力傳感器 M-PAK RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPXM2102DT1 | 功能描述:板上安裝壓力/力傳感器 M-PAK RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPXM2102G | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:100 kPa On-Chip Temperature Compensated & Calibrated Silicon Pressure Sensors |
| MPXM2102GS | 功能描述:板上安裝壓力/力傳感器 M-PAK RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
發布緊急采購，3分鐘左右您將得到回復。