- 您現在的位置：買賣IC網 > PDF目錄25633 > MQ83C154DTXXX-25/883R (ATMEL CORP) 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44 PDF資料下載
參數資料
| 型號： | MQ83C154DTXXX-25/883R |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44 |
| 封裝： | CERAMIC, QFP-44 |
| 文件頁數： | 27/46頁 |
| 文件大?。?/td> | 4720K |
| 代理商： | MQ83C154DTXXX-25/883R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
32
ATtiny20 [DATASHEET]
8235E–AVR–03/2013
Figure 8-7.
Watchdog Timer
The Wathdog Timer can also be configured to generate an interrupt instead of a reset. This can be very helpful when
using the Watchdog to wake-up from Power-down.
To prevent unintentional disabling of the Watchdog or unintentional change of time-out period, two different safety levels
are selected by the fuse WDTON as shown in Table 8-1 on page 32. See “Procedure for Changing the Watchdog Timer
Configuration” on page 32 for details.
Table 8-1.
WDT Configuration as a Function of the Fuse Settings of WDTON
8.4.1
Procedure for Changing the Watchdog Timer Configuration
The sequence for changing configuration differs between the two safety levels, as follows:
8.4.1.1 Safety Level 1
In this mode, the Watchdog Timer is initially disabled, but can be enabled by writing the WDE bit to one without any
restriction. A special sequence is needed when disabling an enabled Watchdog Timer. To disable an enabled Watchdog
Timer, the following procedure must be followed:
1.
Write the signature for change enable of protected I/O registers to register CCP
2.
Within four instruction cycles, in the same operation, write WDE and WDP bits
8.4.1.2 Safety Level 2
In this mode, the Watchdog Timer is always enabled, and the WDE bit will always read as one. A protected change is
needed when changing the Watchdog Time-out period. To change the Watchdog Time-out, the following procedure must
be followed:
1.
Write the signature for change enable of protected I/O registers to register CCP
2.
Within four instruction cycles, write the WDP bit. The value written to WDE is irrelevant
WDTON
Safety Level
Initial State
How to Disable
How to Change Time-out
Unprogrammed
1
Disabled
Protected change sequence
No limitations
Programmed
2
Enabled
Always enabled
Protected change sequence
OSC/2K
OSC/4K
OSC/8K
OSC/16K
OSC/32K
OSC/64K
OSC/128K
OSC/256K
OSC/512K
OSC/1024K
MCU RESET
WATCHDOG
PRESCALER
128 kHz
OSCILLATOR
WATCHDOG
RESET
WDP0
WDP1
WDP2
WDP3
WDE
MUX
相關PDF資料 |
PDF描述 |
|---|---|
| MQ80C52TXXX-12SB | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQFP44 |
| MC80C52CXXX-16 | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 |
| MR80C52EXXX-25/883 | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44 |
| MQ83C154XXX-12/883R | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQFP44 |
| MC80C52CXXX-16P883 | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MQ83C154-L16 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| MQ83C154T-12 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| MQ83C154T-16 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| MQ83C154T-20 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| MQ83C154T-25 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。