国产又大又粗又猛的视频,伊人欧美在线,無碼中文字幕av免費放

您好，
買賣IC網歡迎您。
請登錄
免費注冊

您現在的位置：買賣IC網 > PDF目錄45320 > MQ83C154XXX-L16P883D (TEMIC SEMICONDUCTORS) 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQFP44 PDF資料下載

型號：	MQ83C154XXX-L16P883D
廠商：	TEMIC SEMICONDUCTORS
元件分類：	微控制器/微處理器
英文描述：	8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQFP44
文件頁數：	183/839頁
文件大小：	61013K
代理商：	MQ83C154XXX-L16P883D

ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P [DATASHEET]

8285E–AVR–02/2013

Chip Erase

The Chip Erase will erase the Flash and EEPROM

(1) memories plus Lock bits. The Lock bits are not reset until the

program memory has been completely erased. The Fuse bits are not changed. A Chip Erase must be performed

before the Flash and/or EEPROM are reprogrammed.

1. The EEPRPOM memory is preserved during Chip Erase if the EESAVE Fuse is programmed.

Load Command “Chip Erase”

Set XA1, XA0 to “10”. This enables command loading.

Set BS1 to “0”.

Set DATA to “1000 0000”. This is the command for Chip Erase.

Give XTAL1 a positive pulse. This loads the command.

Give WR a negative pulse. This starts the Chip Erase. RDY/BSY goes low.

Wait until RDY/BSY goes high before loading a new command.

Programming the Flash

The Flash is organized in pages, see Table 27-7 on page 260. When programming the Flash, the program data is

latched into a page buffer. This allows one page of program data to be programmed simultaneously. The following

procedure describes how to program the entire Flash memory:

A. Load Command “Write Flash”

Set XA1, XA0 to “10”. This enables command loading.

Set BS1 to “0”.

Set DATA to “0001 0000”. This is the command for Write Flash.

Give XTAL1 a positive pulse. This loads the command.

B. Load Address Low byte

Set XA1, XA0 to “00”. This enables address loading.

Set BS1 to “0”. This selects low address.

Set DATA = Address low byte (0x00 - 0xFF).

Give XTAL1 a positive pulse. This loads the address low byte.

C. Load Data Low Byte

Set XA1, XA0 to “01”. This enables data loading.

Set DATA = Data low byte (0x00 - 0xFF).

Give XTAL1 a positive pulse. This loads the data byte.

D. Load Data High Byte

Set BS1 to “1”. This selects high data byte.

Set XA1, XA0 to “01”. This enables data loading.

Set DATA = Data high byte (0x00 - 0xFF).

Give XTAL1 a positive pulse. This loads the data byte.

相關PDF資料	PDF描述
MR83C154CXXX-20/883	8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQCC44
MQ83C154CXXX-25P883	8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44
MR83C154TXXX-30/883D	8-BIT, MROM, 30 MHz, MICROCONTROLLER, CQCC44
MQ83C154TXXX-36P883R	8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQFP44
MQ83C154XXX-36P883	8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQFP44

相關代理商/技術參數	參數描述
MQ86	制造商:TE Connectivity 功能描述:
MQ8797BH	制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intel 功能描述:
MQ87C196KC/R	制造商:Rochester Electronics LLC 功能描述:
MQ87C196KD-16/B	制造商:Rochester Electronics LLC 功能描述:
MQ87C196KD-20/R	制造商:Rochester Electronics LLC 功能描述:

發布緊急采購，3分鐘左右您將得到回復。

(若只采購一條型號，填寫一行即可)

*型號	*數量	廠商	批號	封裝

采購需求

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

我的聯系方式

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價