參數資料
型號: MR83C154XXX-12/883
廠商: ATMEL CORP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44
封裝: LCC-44
文件頁數: 23/91頁
文件大小: 19688K
代理商: MR83C154XXX-12/883
34
7707F–AVR–11/10
AT90USB82/162
6.6
External Clock
The device can utilize a external clock source as shown in Figure 6-5. To run the device on an
external clock, the CKSEL Fuses must be programmed as shown in Table 6-1.
Figure 6-5.
External Clock Drive Configuration
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
When applying an external clock, it is required to avoid sudden changes in the applied clock fre-
quency to ensure stable operation of the MCU. A variation in frequency of more than 2% from
one clock cycle to the next can lead to unpredictable behavior. If changes of more than 2% is
required, ensure that the MCU is kept in Reset during the changes.
Note that the System Clock Prescaler can be used to implement run-time changes of the internal
clock frequency while still ensuring stable operation. Refer to “System Clock Prescaler” on page
34 for details.
6.7
Clock Output Buffer
The device can output the system clock on the CLKO pin. To enable the output, the CKOUT
Fuse has to be programmed. This mode is suitable when the chip clock is used to drive other cir-
cuits on the system. The clock also will be output during reset, and the normal operation of I/O
pin will be overridden when the fuse is programmed. Any clock source, including the internal RC
Oscillator, can be selected when the clock is output on CLKO. If the System Clock Prescaler is
used, it is the divided system clock that is output.
6.8
System Clock Prescaler
The AT90USB82/162 has a system clock prescaler, and the system clock can be divided by set-
ting the “Clock Prescale Register – CLKPR” on page 35. This feature can be used to decrease
Table 6-8.
Start-up Times for the External Clock Selection
Power Conditions
Start-up Time from Power-
down and Power-save
Additional Delay from
Reset (VCC = 5.0V)
SUT1..0
BOD enabled
6 CK
14CK
00
Fast rising power
6 CK
14CK + 4.1 ms
01
Slowly rising power
6 CK
14CK + 65 ms
10
Reserved
11
NC
EXTERNAL
CLOCK
SIGNAL
XTAL2
XTAL1
GND
相關PDF資料
PDF描述
MD83C154CXXX-L16P883D 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40
MC80C52TXXX-12P883D 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CDIP40
MQ80C52TXXX-36P883 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQFP44
MQ83C154TXXX-L16/883D 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQFP44
MQ80C154-36P883 8-BIT, 36 MHz, MICROCONTROLLER, CQFP44
相關代理商/技術參數
參數描述
MR850 功能描述:整流器 3.0 Amp 50 Volt 150ns RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
MR850 _AY _10001 制造商:PanJit Touch Screens 功能描述:
MR850 R0 制造商:SKMI/Taiwan 功能描述:Diode Switching 50V 3A 2-Pin DO-201AD T/R
MR850_ R2 _10001 制造商:PanJit Touch Screens 功能描述:
MR850_09 制造商:PANJIT 制造商全稱:Pan Jit International Inc. 功能描述:SOFT RECOVERY, FAST SWITCHING PLASTIC RECTIFIER