- 您現在的位置：買賣IC網 > PDF目錄98045 > MSM9005-XXGS-BK (LAPIS SEMICONDUCTOR CO LTD) 8 X 65 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP100 PDF資料下載
參數資料
| 型號： | MSM9005-XXGS-BK |
| 廠商： | LAPIS SEMICONDUCTOR CO LTD |
| 元件分類： | 顯示控制器 |
| 英文描述： | 8 X 65 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP100 |
| 封裝： | 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 13/31頁 |
| 文件大小： | 315K |
| 代理商： | MSM9005-XXGS-BK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Semiconductor
MSM9005-xx
19/30
FEDL9005-03
2. Display on/off command (DISP command)
This command is used to select LCD panel display-on mode and display-off mode. Setting
DI = "0" enters display-off mode. At this time, the output voltage of all segments and common
output pins go to VDD level and the LCD panel goes out. Setting DI = "1" enters display-on
mode. At this time, the LCD panel restarts the status display before entering display-off
mode.
[DISP command format]
100*100
DI
D8 D7 D6 D5 D4 D3 D2 D1
DISP
command
Display-off mode is set when DI = “0”
Display-on mode is set when DI = “1”
*: Don't care
3. Arbitrator Blink Control 1/5 command (ABBC 1/5 command)
This command is used to select the type of writing arbitrator blink data to the Arbitrator Blink
RAM (ABB RAM). This command is used along with the Character Blink on/off command
or with the Arbitrator Blink command, explained below.
Setting BC = "0" enables writing arbitrator blink data in 5-bit units using the CHB command.
Setting BC = "1" enables writing arbitrator blink data in 1 bit unit using the ABB command.
[ABBC 1/5 command format]
1001110
BC
D8 D7 D6 D5 D4 D3 D2 D1
DISP
command
BC = "0" enables writing in 5-bit unit.
BC = "1" enables writing in 1-bit unit.
4. Character Blink on/off command (CHB command)
This command is used to blink a character and arbitrator in 5-dot units. Blinking can be set
for each address pointer value. This command is used with the ABBC 1/5 command,
explained above.
If CB = "0" is set when the address pointer value is 00H to 0CH, "0" is written to Character Blink
RAM (CHB RAM), and the blinking of a character displayed in the segments corresponding
to the address pointer value stops. If CB = "1" is set, "1" is written to CHB RAM, and the
character displayed in the segments corresponding to the address pointer value starts
blinking.
If CB = "0" is set when the address pointer value is 10H to 1CH, "0" is written to the arbitrator
blink RAM (ABB RAM) and the blinking of the arbitrator displayed in the segments
corresponding to the address pointer value stops. If CB = "1" is set, "1" is written to the ABB
RAM, and the arbitrator displayed in the segments corresponding to the address pointer
value starts blinking.
Set the address pointer value by the LPA command before executing this command.
Transfer the LPA command, ABBC 1/5 command and CHB command as follows.
相關PDF資料 |
PDF描述 |
|---|---|
| MSM9202-XXGS-K | 16 X 37 DOTS FLUORESCENT DSPL CTRL, PDSO64 |
| MSM9225GA-2K | 2 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PQFP44 |
| MSP430A017IPNR | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP80 |
| MSP430F2274MRHAEP | 16-BIT, FLASH, RISC MICROCONTROLLER, PQCC40 |
| MSP430F2619SKGD1 | 16-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, UUC82 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSM9006-01 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Driver with Keyscan Function |
| MSM9006-01GS-BK | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Driver with Keyscan Function |
| MSM9006-02 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Driver with Keyscan Function |
| MSM9006-02GS-BK | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Driver with Keyscan Function |
| MSM9006-02GS-BK-7 | 功能描述:LCD 驅動器 LCD Controller 1/4 Duty RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。