- 您現在的位置：買賣IC網 > PDF目錄69040 > MSP430A004IPWR (TEXAS INSTRUMENTS INC) 16-BIT, 8 MHz, RISC MICROCONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | MSP430A004IPWR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, 8 MHz, RISC MICROCONTROLLER, PDSO20 |
| 封裝： | PLASTIC, TSSOP-20 |
| 文件頁數： | 33/47頁 |
| 文件大?。?/td> | 917K |
| 代理商： | MSP430A004IPWR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
MSP430x11x2, MSP430x12x2
MIXED SIGNAL MICROCONTROLLER
SLAS361D JANUARY 2002 REVISED AUGUST 2004
39
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
JTAG fuse check mode
MSP430 devices that have the fuse on the TEST terminal have a fuse check mode that tests the continuity of
the fuse the first time the JTAG port is accessed after a power-on reset (POR). When activated, a fuse check
current, ITF, of 1 mA at 3 V, 2.5 mA at 5 V can flow from the TEST pin to ground if the fuse is not burned. Care
must be taken to avoid accidentally activating the fuse check mode and increasing overall system power
consumption.
When the TEST pin is taken back low after a test or programming session, the fuse check mode and sense
currents are terminated.
Activation of the fuse check mode occurs with the first negative edge on the TMS pin after power up or if TMS
is being held low during power up. The second positive edge on the TMS pin deactivates the fuse check mode.
After deactivation, the fuse check mode remains inactive until another POR occurs. After each POR the fuse
check mode has the potential to be activated.
The fuse check current will only flow when the fuse check mode is active and the TMS pin is in a low state (see
Figure 10). Therefore, the additional current flow can be prevented by holding the TMS pin high (default
condition).
Time TMS Goes Low After POR
TMS
ITF
ITEST
Figure 10. Fuse Check Mode Current, MSP430F11x2, MSP430F12x2
NOTE:
The CODE and RAM data protection is ensured if the JTAG fuse is blown and the 256-bit bootloader
access key is used. Also, see the bootstrap loader section for more information.
相關PDF資料 |
PDF描述 |
|---|---|
| MSP430A005IPWR | 16-BIT, 8 MHz, RISC MICROCONTROLLER, PDSO28 |
| MSP430A004IPW | 16-BIT, 8 MHz, RISC MICROCONTROLLER, PDSO20 |
| MSP430A019IRHBR | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC64 |
| MSP430A019IRHBT | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC64 |
| MSP430C111IJL | 16-BIT, MROM, RISC MICROCONTROLLER, CDIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSP430A005IPW | 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER |
| MSP430A005IPWR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER |
| MSP430A009IPM | 制造商:Texas Instruments 功能描述: |
| MSP430A009IPMR | 功能描述:16位微控制器 - MCU 16B Ultra-Lo-Pwr Microcntrlr,48kB Fl RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MSP430A010IPMR | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。