參數資料
型號： MSP430C413CY
廠商： TEXAS INSTRUMENTS INC
元件分類： 微控制器/微處理器
英文描述： 16-BIT, MROM, 8 MHz, RISC MICROCONTROLLER, UUC
文件頁數： 31/64頁
文件大小： 1242K
代理商： MSP430C413CY
MSP430x41x
MIXED SIGNAL MICROCONTROLLER
SLAS340J MAY 2001 REVISED DECEMBER 2008
37
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
flash memory
PARAMETER
TEST
CONDITIONS
VCC
MIN
TYP
MAX
UNIT
VCC(PGM/
ERASE)
Program and erase supply voltage
2.7
3.6
V
fFTG
Flash timing generator frequency
257
476
kHz
IPGM
Supply current from DVCC during program
2.7 V/ 3.6 V
3
5
mA
IERASE
Supply current from DVCC during erase
2.7 V/ 3.6 V
3
7
mA
tCPT
Cumulative program time
See Note 1
2.7 V/ 3.6 V
10
ms
tCMErase
Cumulative mass erase time
See Note 2
2.7 V/ 3.6 V
200
ms
Program/erase endurance
104
105
cycles
tRetention
Data retention duration
TJ = 25°C
100
years
tWord
Word or byte program time
35
tBlock, 0
Block program time for 1st byte or word
30
tBlock, 1-63
Block program time for each additional byte or word
See Note 3
21
t
tBlock, End
Block program end-sequence wait time
See Note 3
6
tFTG
tMass Erase
Mass erase time
5297
tSeg Erase
Segment erase time
4819
NOTES:
1. The cumulative program time must not be exceeded when writing to a 64-byte flash block. This parameter applies to all programming
methods: individual word/byte write and block write modes.
2. The mass erase duration generated by the flash timing generator is at least 11.1 ms ( = 5297x1/fFTG,max = 5297x1/476kHz). To
achieve the required cumulative mass erase time the flash controller’s mass erase operation can be repeated until this time is met.
(A worst case minimum of 19 cycles are required).
3. These values are hardwired into the flash controller’s state machine (tFTG = 1/fFTG).
JTAG interface
PARAMETER
TEST
CONDITIONS
VCC
MIN
TYP
MAX
UNIT
f
TCK input frequency
see Note 1
2.2 V
0
5
MHz
fTCK
TCK input frequency
see Note 1
3 V
0
10
MHz
RInternal
Internal pull-up resistance on TMS, TCK, TDI/TCLK
see Note 2
2.2 V/ 3 V
25
60
90
k
Ω
NOTES:
1. fTCK may be restricted to meet the timing requirements of the module selected.
2. TMS, TDI/TCLK, and TCK pullup resistors are implemented in all versions.
JTAG fuse (see Note 1)
PARAMETER
TEST
CONDITIONS
MIN
MAX
UNIT
VCC(FB)
Supply voltage during fuse-blow condition
TA = 25°C
2.5
V
Voltage level on TDI/TCLK for fuse blow
MSP430C41x
3.5
3.9
V
VFB
Voltage level on TDI/TCLK for fuse-blow
MSP430F41x
6
7
V
IFB
Supply current into TDI/TCLK during fuse blow
100
mA
tFB
Time to blow fuse
1
ms
NOTES:
1. Once the fuse is blown, no further access to the MSP430 via JTAG/Test is possible. The JTAG block is switched to bypass mode.
相關PDF資料
PDF描述
MSP430F413IPMR 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP64
MSP430F4260IRGZ 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC48
MSP430F4260IRGZR 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC48
MSP430F4260IRGZT 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC48
MSP430F4260IDL 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO48
相關代理商/技術參數
參數描述
MSP430C413IPM 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER
MSP430C413IRTD 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER
MSP430-CCRF 功能描述:開發板和工具包 - MSP430 868 / 915MHZ TRANS FOR CC430F5137 RoHS:否 制造商:Olimex Ltd. 產品:Development Boards 工具用于評估:MSP430F5510 核心:MSP430 接口類型:JTAG, USB 工作電源電壓:5 V
MSP430-CCRFLCD 功能描述:開發板和工具包 - MSP430 868 / 915MHZ TRANS & LCD FOR CC430F5137 RoHS:否 制造商:Olimex Ltd. 產品:Development Boards 工具用于評估:MSP430F5510 核心:MSP430 接口類型:JTAG, USB 工作電源電壓:5 V
MSP430CG4616IPZ 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*