- 您現在的位置：買賣IC網 > PDF目錄98045 > MSP430P325IPG (TEXAS INSTRUMENTS INC) 16-BIT, OTPROM, 3.3 MHz, RISC MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MSP430P325IPG |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, OTPROM, 3.3 MHz, RISC MICROCONTROLLER, PQFP64 |
| 封裝： | GREEN, PLASTIC, QFP-64 |
| 文件頁數： | 4/37頁 |
| 文件大?。?/td> | 534K |
| 代理商： | MSP430P325IPG |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
MSP430P325
MIXED SIGNAL MICROCONTROLLER
SLAS164A – FEBRUARY 1998 – REVISED MARCH 2000
12
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
8-Bit Timer/Counter
The 8-Bit interval timer supports three major functions for the application:
D Serial communication or data exchange
D Pulse counting or pulse accumulation
D Timer
The 8-Bit Timer/Counter peripheral includes the following major blocks: an 8-Bit up-counter with preload
register, an 8-Bit control register, an input clock selector, an edge detection (e.g. Start bit detection for
asynchronous protocols), and an input and output data latch, triggered by the carry-out-signal from the 8-Bit
counter.
The 8-Bit counter counts up with an input clock which is selected by two control bits from the control register.
The four possible clock sources are MCLK, ACLK, the external signal from terminal P0.1, and the signal from
the logical AND of MCLK and terminal P0.1.
Two counter inputs (load, enable) control the counter operation. The load input controls load operations. A
write-access to the counter results in loading the content of the preload register into the counter. The software
writes or reads the preload register with all instructions. The preload register acts as a buffer and can be written
immediately after the load of the counter is completed. The enable input enables the count operation. When
the enable signal is set to high, the counter will count-up each time a positive clock edge is applied to the clock
input of the counter.
Serial protocols, like UART protocol, need start-bit edge-detection to determine, at the receiver, the start of a
data transmission. When this function is activated, the counter starts counting after the start-bit condition is
detected. The first signal level is sampled into the RXD input data-latch after completing the first timing interval,
which is programmed into the counter. Two latches are used for input and output data (RXD_FF and TXD_FF)
are clocked by the counter after the programmed timing interval has elapsed.
UART
The serial communication uses software and the 8-Bit Timer/Counter hardware. The hardware supports the
output of the serial data stream, bit-by-bit, with the timing determined by the counter. The software/hardware
interface connects the mixed signal controller to external devices, systems, or networks.
Timer/Port
The Timer/Port module has two 8-Bit counters, an input that triggers one counter, and six 3-state digital outputs.
Both counters have an independent clock-selector for selecting an external signal or one of the internal clocks
(ACLK or MCLK). One of the counters has an extended control capability to halt, count continuously, or gate
the counter by selecting one of two external signals. This gate signal sets the interrupt flag, if an external signal
is selected, and the gate stops the counter.
Both timers can be read from and written to by software. The two 8-Bit counters can be cascaded to a 16-bit
counter. A common interrupt vector is implemented. The interrupt flag can be set from three events in the 8-Bit
counter mode (gate signal, overflow from the counters) or from two events in the 16-bit counter mode (gate
signal, overflow from the MSB of the cascaded counter).
相關PDF資料 |
PDF描述 |
|---|---|
| MSP430P337AIPJM | 16-BIT, OTPROM, 3.8 MHz, RISC MICROCONTROLLER, PQFP100 |
| MSW2002-200-T | SILICON, PIN DIODE |
| MT8952BC | 1 CHANNEL(S), 2.5M bps, SERIAL COMM CONTROLLER, CDIP28 |
| MT8952BC | 1 CHANNEL(S), 2.5M bps, SERIAL COMM CONTROLLER, CDIP28 |
| MT8LLN22NCNE | PCI BUS CONTROLLER, PBGA316 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSP430P325IPM | 功能描述:16位微控制器 - MCU 16kB OTP 512B RAM 14b ADC/84 seg LCD RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MSP430P325QPG | 制造商:Texas Instruments 功能描述: |
| MSP430P337AIPJM | 功能描述:16位微控制器 - MCU 32kB OTP 1KB RAM USART/120 seg LCD RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MSP430P337AIPJM | 制造商:Texas Instruments 功能描述:16-Bit Microcontroller Clock Speed:3.8MH |
| MSP430P337AIPJMPX | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。