- 您現在的位置：買賣IC網 > PDF目錄45322 > MT80C31-25D (ATMEL CORP) 8-BIT, 25 MHz, MICROCONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | MT80C31-25D |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, 25 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | 1 MM HEIGHT, QFP-44 |
| 文件頁數： | 15/170頁 |
| 文件大小： | 4133K |
| 代理商： | MT80C31-25D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁
111
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
15.4.3
Programming the Flash
The Flash can be written word-by-word. Before writing a Flash word, the Flash target location must be erased.
Writing to an un-erased Flash word will corrupt its content.
The Flash is word-accessed for writing, and the data space uses byte-addressing to access Flash that has been
mapped to data memory. It is therefore important to write the word in the correct order to the Flash, namely low
bytes before high bytes. First, the low byte is written to the temporary buffer. Then, writing the high byte latches
both the high byte and the low byte into the Flash word buffer, starting the write operation to Flash.
The Flash erase operations can only performed for the entire Flash sections.
The Flash programming sequence is as follows:
1.
Perform a Flash section erase or perform a Chip erase
2.
Write the Flash section word by word
15.4.3.1
Chip Erase
The Chip Erase command will erase the entire code section of the Flash memory and the NVM Lock Bits. For
security reasons, the NVM Lock Bits are not reset before the code section has been completely erased. Configura-
tion, Signature and Calibration sections are not changed.
Before starting the Chip erase, the NVMCMD register must be loaded with the CHIP_ERASE command. To start
the erase operation a dummy byte must be written into the high byte of a word location that resides inside the Flash
code section. The NVMBSY bit remains set until erasing has been completed. While the Flash is being erased nei-
ther Flash buffer loading nor Flash reading can be performed.
The Chip Erase can be carried out as follows:
1.
Write the CHIP_ERASE command to the NVMCMD register
2.
Start the erase operation by writing a dummy byte to the high byte of any word location inside the code
section
3.
Wait until the NVMBSY bit has been cleared
15.4.3.2
Erasing the Code Section
The algorithm for erasing all pages of the Flash code section is as follows:
1.
Write the SECTION_ERASE command to the NVMCMD register
2.
Start the erase operation by writing a dummy byte to the high byte of any word location inside the code
section
3.
Wait until the NVMBSY bit has been cleared
15.4.3.3
Writing a Code Word
The algorithm for writing a word to the code section is as follows:
1.
Write the WORD_WRITE command to the NVMCMD register
2.
Write the low byte of the data into the low byte of a word location
3.
Write the high byte of the data into the high byte of the same word location. This will start the Flash write
operation
4.
Wait until the NVMBSY bit has been cleared
相關PDF資料 |
PDF描述 |
|---|---|
| MS80C31-20D | 8-BIT, 20 MHz, MICROCONTROLLER, PQCC44 |
| MS80C51T-20D | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQCC44 |
| MT80C51T-20R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP44 |
| MS80C51-25D | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44 |
| MP80C51C-30D | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT80C31BH | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intel 功能描述: |
| MT80C51BH | 制造商:ROCHESTER 制造商全稱:ROCHESTER 功能描述:CMOS SINGLE - CHIP 8-BIT MICROCOMPUTER 64K program Memory Space |
| MT80C51FB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MT80C51FB/B | 制造商:Intel 功能描述: |
| MT80GB | 制造商:Datak Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。