- 您現在的位置：買賣IC網 > PDF目錄383642 > MT88L89AS (Mitel Networks Corporation) 3V Integrated DTMFTransceiver with Adaptive Micro Interface PDF資料下載
參數資料
| 型號： | MT88L89AS |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | 3V Integrated DTMFTransceiver with Adaptive Micro Interface |
| 中文描述： | 3V的綜合DTMFTransceiver自適應微型接口 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 352K |
| 代理商： | MT88L89AS |
Advance Information
MT88L89
4-135
Table 7
.
Control Register B Description
Table 8
.
Status Register Description
BIT
NAME
DESCRIPTION
b0
BURST
Burst Mode Select. A logic high de-activates burst mode; a logic low enables burst mode.
When activated, the digital code representing a DTMF signal (see Table 1) can be written
to the transmit register, which will result in a transmit DTMF tone burst and pause of equal
durations (typically 51 msec). Following the pause, the status register will be updated (b1 -
Transmit Data Register Empty), and an interrupt will occur if the interrupt mode has been
enabled.
When CP mode (control register A, b1) is enabled the normal tone burst and pause
durations are extended from a typical duration of 51 msec to 102 msec.
When BURST is high (de-activated) the transmit tone burst duration is determined by the
TOUT bit (control register A, b0).
b1
RxEN
This bit enables the DTMF and Call Progress Tone receivers. A logic low enables both
circuits. A logic high deactivates and puts both receiver circuits into power down mode.
b2
S/D
Single or Dual Tone Generation. A logic high selects the single tone output; a logic low
selects the dual tone (DTMF) output. The single tone generation function requires further
selection of either the row or column tones (low or high group) through the C/R bit (control
register B, b3).
b3
C/R
Column or Row Tone Select. A logic high selects a column tone output; a logic low selects
a row tone output. This function is used in conjunction with the S/D bit (control register B,
b2).
BIT
NAME
STATUS FLAG SET
STATUS FLAG CLEARED
b0
IRQ
Interrupt has occurred. Bit one
(b1) or bit two (b2) is set.
Interrupt is inactive. Cleared after
Status Register is read.
b1
TRANSMIT DATA
REGISTER EMPTY
(BURST MODE ONLY)
Pause duration has terminated
and transmitter is ready for new
data.
Cleared after Status Register is
read or when in non-burst mode.
b2
RECEIVE DATA REGISTER
FULL
Valid data is in the Receive Data
Register.
Cleared after Status Register is
read.
b3
DELAYED STEERING
Set upon the valid detection of
the absence of a DTMF signal.
Cleared upon the detection of a
valid DTMF signal.
相關PDF資料 |
PDF描述 |
|---|---|
| MT88V32 | 8 x 4 High Performance Video Switch Array |
| MT88V32AP | 8 x 4 High Performance Video Switch Array |
| MT8920B | ST-BUS Parallel Access Circuit(串行通信總線（ST-Bus）并行存取電路（在ST總線和并行系統間提供一個簡單接口）) |
| MT8924-1 | PCM Conference Circuit (PCC) Preliminary Information |
| MT8924AE | PCM Conference Circuit (PCC) Preliminary Information |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT88L89AS1 | 制造商:Microsemi Corporation 功能描述:DTMF TXRX 3.58MHZ CMOS 3V 20SOIC - Rail/Tube 制造商:Microsemi Corporation 功能描述:PB FREE 3V DTMF TRANSCEIVER 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX DTMF 3V 20SOIC 制造商:Microsemi Corporation 功能描述:IC TXRX DTMF 3V 20SOIC |
| MT88L89ASR | 制造商:Microsemi Corporation 功能描述: |
| MT88L89ASR1 | 制造商:Microsemi Corporation 功能描述:PB FREE 3V DTMF TRANSCEIVER 制造商:Microsemi Corporation 功能描述:DTMF TXRX 3.58MHZ CMOS 3V 20SOIC - Tape and Reel 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX DTMF 3V 20SOIC 制造商:Microsemi Corporation 功能描述:IC TXRX DTMF 3V 20SOIC |
| MT88V32 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:8 x 4 High Performance Video Switch Array |
| MT88V32AP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:8 x 4 High Performance Video Switch Array |
發布緊急采購，3分鐘左右您將得到回復。