參數資料
型號: MT9125AP
廠商: Mitel Networks Corporation
英文描述: CMOS Dual ADPCM Transcoder
中文描述: CMOS雙差分PcM碼器
文件頁數: 3/16頁
文件大小: 299K
代理商: MT9125AP
Preliminary Information
MT9125
8-19
6
7
BCLK
Bit Clock input for both PCM and ADPCM ports; used in SSI mode only. The falling edge of
this clock is used to clock data in on DSTi and ADPCMi. The rising edge is used to clock
data out on DSTo and ADPCMo. Can be any rate between 128 kHz and 2.048 MHz. Refer
to the serial timing diagrams of Figures 12 and 13. When not used, this pin should be tied
to V
SS
.
This is a TTL level input.
7
8
V
SS
ENB2
Power supply ground (0 volts).
8
10
Enable Strobe input for B2 channel PCM timing in SSI mode only. A valid 8-bit strobe must
be present at this input if there are no ST-BUS signals at F0i and MCLK. When the device
detects a valid frame pulse at F0i, PCM timing for the B2 ST-BUS channel is decoded
internally and the ENB2 input is ignored. When not used this pin should be tied to V
SS
.
This is a TTL level input.
9
11
ENB1
Enable Strobe input for B1 channel PCM timing in SSI mode only. A valid 8-bit strobe must
be present at this input if there are no ST-BUS signals at F0i and MCLK. When the device
detects a valid frame pulse at F0i, PCM timing for the B1 ST-BUS channel is decoded
internally and the ENB1 input is ignored. When not used this pin should be tied to V
SS
.
This is a TTL level input.
10,
11
12,
13
MS1,
MS2
Mode select control input pins 1 and 2 for the B1 channel according to the following:
MS2
MS1
B1 Channel
0
0
algorithm reset
0
1
ADPCM bypass mode (24 or 32 kbit/s)
1
0
24 kbit/s ADPCM mode
1
1
32 kbit/s ADPCM mode
These are TTL level inputs.
12,
13
14,
16
MS3,
MS4
Mode select control input pins 3 and 4 for the B2 channel according to the following:
MS4
MS3
B2 Channel
0
0
algorithm reset
0
1
ADPCM bypass mode (24 or 32 kbit/s)
1
0
24 kbit/s ADPCM mode
1
1
32 kbit/s ADPCM mode
These are TTL level inputs.
14
17
A/μ
Law select input. Selects μ-Law when low, A-Law when high.
This is a TTL level input.
15
18
FORMAT Format select input. Selects CCITT PCM coding if high, or SIGN MAGNITUDE PCM if low.
This is a TTL level input.
16
19
PWRDN Power Down input. Logic low on this pin forces the device to assume an internal power
down mode where all operation is halted. This mode minimizes power consumption.
Outputs are tri-stated. This is a schmidt trigger input.
17
20
IC
Internal Connection. Tie to V
SS
for normal operation.
Positive power supply input, 5 volts ± 10%.
18
22
V
DD
ENA
19
23
Enable Strobe input for both input and output ADPCM channels; used for SSI operation
only. Refer to Figure 3. When not used, tie to VSS.
This is a TTL level input.
20
24
ADPCMi Serial ADPCM word input data stream. Refer to the serial timing diagram of Fig. 13. This is
a TTL level input.
21
25
ADPCMo Serial ADPCM word output stream. Refer to the serial timing diagram of Fig.13.
Pin Description (continued)
Pin #
Name
Description
DIP
PLCC
相關PDF資料
PDF描述
MT9126AE CMOS Quad ADPCM Transcoder
MT9126AS CMOS Quad ADPCM Transcoder
MT9126 Quad ADPCM Transcoder(四ADPCM編解碼器)
MT9160B ISO2-CMOS 5 Volt Multi-Featured Codec (MFC)
MT9160BE ISO2-CMOS 5 Volt Multi-Featured Codec (MFC)
相關代理商/技術參數
參數描述
MT9126 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS Quad ADPCM Transcoder
MT9126AE 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS Quad ADPCM Transcoder
MT9126AE1 制造商:Microsemi Corporation 功能描述:ADPCM VOICE COMPRESSION G.726 16KBPS/24KBPS/32KBPS 5V 28PDIP - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TRANSCODER QUAD ADPCM 28PDIP 制造商:Microsemi Corporation 功能描述:IC TRANSCODER QUAD ADPCM 28PDIP
MT9126AS 制造商:Microsemi Corporation 功能描述:
MT9126AS1 制造商:Microsemi Corporation 功能描述:ADPCM VOICE COMPRESSION G.726 16KBPS/24KBPS/32KBPS 5V 28SOIC - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TRANSCODER QUAD ADPCM 28SOIC 制造商:Microsemi Corporation 功能描述:IC TRANSCODER QUAD ADPCM 28SOIC