- 您現在的位置：買賣IC網 > PDF目錄383645 > MT9161BE (Mitel Networks Corporation) ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) PDF資料下載
參數資料
| 型號： | MT9161BE |
| 廠商： | Mitel Networks Corporation |
| 元件分類： | Codec |
| 英文描述： | ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) |
| 中文描述： | ISO2 - 5伏的CMOS多精選編解碼器（MFC）中 |
| 文件頁數： | 7/30頁 |
| 文件大?。?/td> | 154K |
| 代理商： | MT9161BE |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Advance Information
MT9160B/61B
85
supports a strobed data interface found on many
standard Codec devices. This interface is commonly
referred to as Simple Serial Interface (SSI). The
combination of ST-BUS and SSI provides a Flexible
Digital Interface (FDI) capable of supporting all Mitel
basic rate transmission devices as well as many
other 2B+D transceivers.
The required mode of operation is selected via the
CSL2-0 control bits (Control Register 2, address
04h). Pin definitions alter dependent upon the
operational mode selected, as described in the
following subsections as well as in the Pin
Description tables.
Quiet Code
The FDI can be made to send quiet code to the
decoder and receive filter path by setting the RxMute
bit high. Likewise, the FDI will send quiet code in the
transmit path when the TxMute bit is high. Both of
these control bits reside in Control Register 1 at
address 03h. When either of these bits are low their
respective paths function normally. The -Zero entry
of Table 1 is used for the quiet code definition.
ST-BUS Mode
The ST-BUS consists of output (DSTo) and input
(DSTi) serial data streams, in FDI these are named
Dout and Din respectively, a synchronous clock input
signal CLOCKin (C4i), and a framing pulse input
(F0i). These signals are direct connections to the
corresponding pins of Mitel basic rate devices. The
CSL2, CSL1 and CSL0 bits are set to 1 for ST-BUS
operation.
The data streams operate at 2048 kb/s and are Time
Division Multiplexed into 32 identical channels of 64
kb/s bandwidth. A frame pulse (a 244 nSec low going
pulse) is used to separate the continuous serial data
streams into the 32 channel TDM frames. Each
frame has a 125
μ
Second period translating into an 8
kHz frame rate. A valid frame begins when F0i is
logic low coincident with a falling edge of C4i. Refer
to figure 11 for detailed ST-BUS timing. C4i has a
frequency (4096 kHz) which is twice the data rate.
This clock is used to sample the data at the 3/4
bit-cell position on DSTi and to make data available
on DSTo at the start of the bit-cell. C4i is also used to
clock the MT9160B/61B internal functions (i.e.,
Filter/Codec, Digital gain and tone generation) and to
provide the channel timing requirements.
The MT9160B/61B uses only the first four channels
of the 32 channel frame. These channels are always
defined, beginning with Channel 0 after the frame
pulse, as shown in Figure 6 (ST-BUS channel
assignments). The MT9161B provides a delayed
frame pulse (F0od), 4 channels after the input frame
pulse.
The first two (D & C) Channels are enabled for use
by the DEN and CEN bits respectively, (Control
Register 2, address 04h). ISDN basic rate service
(2B+D) defines a 16 kb/s signalling (D) Channel. The
MT9160B/61B supports transparent access to this
signalling channel. ST-BUS basic rate transmission
devices, which may not employ a microport, provide
access to their internal control/status registers
through the ST-BUS Control (C) Channel. The
MT9160B/61B supports microport access to this
C-Channel.
DEN - D-Channel
In ST-BUS mode access to the D-Channel (transmit
and receive) data is provided through an 8-bit read/
write register (address 06h). D-Channel data is
accumulated in, or transmitted from this register at
the rate of 2 bits/frame for 16 kb/s operation (1 bit/
frame for 8 kb/s operation). Since the ST-BUS is
asynchronous, with respect to the microport, valid
access to this register is controlled through the use
of an interrupt (IRQ) output. D-Channel access is
enabled via the (DEn) bit.
Figure 6 - ST-BUS Channel Assignment
F0i
DSTi,
DSTo
LSB first
for D-
Channel
MSB first for C, B1- & B2-
Channels
CHANNEL 0
D-channel
CHANNEL 1
C-channel
CHANNEL 2
B1-channel
CHANNEL 3
B2-channel
CHANNELS 4-31
Not Used
125
μ
s
F0od
相關PDF資料 |
PDF描述 |
|---|---|
| MT9161BN | ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) |
| MT9161BS | ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) |
| MT9160B | 5 Volt Multi-Featured Codec (MFC)(5V 多特性編解碼器) |
| MT9161B | 5 Volt Multi-Featured Codec (MFC)(5V 多特性編解碼器) |
| MT9162 | ISO2-CMOS 5 Volt Single Rail Codec |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9161BN | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) |
| MT9161BS | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:5 Volt Multi-Featured Codec (MFC) |
| MT9162 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:5 Volt Single Rail Codec |
| MT9162AE | 制造商:Microsemi Corporation 功能描述:CODEC 20PDIP - Rail/Tube |
| MT9162AN | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:5 Volt Single Rail Codec |
發布緊急采購，3分鐘左右您將得到回復。