- 您現在的位置：買賣IC網 > PDF目錄9766 > MXL1543BCAI+T (Maxim Integrated Products)IC TXRX MULTIPROTOCOL 28-SSOP PDF資料下載
參數資料
| 型號： | MXL1543BCAI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX MULTIPROTOCOL 28-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 3/3 |
| 規程： | RS232 |
| 電源電壓： | 5VDC |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 帶卷 (TR) |
MXL1543B
+5V Multiprotocol, 3Tx/3Rx, Software-
Selectable Clock/Data Transceivers
12
______________________________________________________________________________________
voltage (B - A) is
≥ -25mV, R_OUT is logic HIGH. If (B -
A) is
≤ -200mV, R_OUT is logic LOW. In the case of a
terminated bus with all transmitters disabled, the
receiver’s differential input voltage is pulled to zero by
the termination. With the receiver thresholds of the
MXL1543B, this results in a logic HIGH with a 25mV
minimum noise margin.
Applications Information
Capacitor Selection
The capacitors used for the charge pumps, as well as
for supply bypassing, should have a low equivalent
series resistance (ESR) and low temperature coeffi-
cient. Multilayer ceramic capacitors with an X7R dielec-
tric offer the best combination of performance, size,
and cost. The flying capacitors (C1, C2) and the
bypass capacitor (C4) should have a value of 1F,
while the reservoir capacitors (C3, C5) should have a
minimum value of 4.7F (Figure 10). To reduce the rip-
ple present on the transmitter outputs, capacitors C3,
C4, and C5 can be increased. The values of C1 and C2
should not be increased.
Cable Termination
The MXL1344A software-selectable resistor network is
designed to be used with the MXL1543B. The
MXL1344A multiprotocol termination network provides
V.11- and V.35-compliant termination, while V.28
receiver termination is internal to the MXL1543B. These
cable termination networks provide compatibility with
V.11, V.28, and V.35 protocols. Using the MXL1344A
termination networks provide the advantage of not hav-
ing to build expensive termination networks out of resis-
tors and relays, manually changing termination
modules, or building custom termination networks
Cable-Selectable Mode
A cable-selectable multiprotocol interface is shown in
Figure 11. The mode control lines M0, M1, and
DCE/DTE are wired to the DB-25 connector. To select
the serial interface mode, the appropriate combination
of M0, M1, and DCE/DTE are grounded within the cable
wiring. The control lines that are not grounded are
pulled high by the internal pullups on the MXL1543B.
The serial interface protocol of the MXL1543B,
MXL1544/MAX3175, and MXL1344A is selected based
on the cable that is connected to the DB-25 interface.
V.11 Interface
As shown in Figure 12, the V.11 protocol is a fully bal-
anced differential interface. The V.11 driver generates a
minimum of ±2V between nodes A and B when a 100
(min) resistance is presented at the load. The V.11
receiver is sensitive to ±200mV differential signals at
receiver inputs A’ and B’. The V.11 receiver rejects
common-mode signals developed across the cable
(referenced from C to C’) of up to ±7V, allowing for
error-free reception in noisy environments. The receiver
inputs must comply with the impedance curve shown in
Figure 13.
For high-speed data transmission, the V.11 specifica-
tion recommends terminating the cable at the receiver
with a 100
resistor. This resistor, although not
required, prevents reflections from corrupting transmit-
ted data. In Figure 14, the MXL1344A is used to termi-
nate the V.11 receiver. Internal to the MXL1344A, S1 is
closed and S2 is open to present a 100
minimum dif-
ferential resistance. The MXL1543B’s internal V.28 ter-
mination is disabled by opening S3.
V.35 Interface
Figure 15 shows a fully-balanced, differential standard
V.35 interface. The generator and the load must both
present a 100
±10 differential impedance and a
150
±15 common-mode impedance as shown by
the resistive T networks in Figure 15. The V.35 driver
generates a current output (±11mA, typ) that develops
an output voltage of ±550mV across the generator and
load termination networks. The V.35 receiver is sensi-
tive to ±200mV differential signals at receiver inputs A’
and B’. The V.35 receiver rejects common-mode sig-
100
MIN
A
′
B
′
C
′
A
B
C
GND
GENERATOR
BALANCED
INTERCONNECTING
CABLE
TERMINATION
RECEIVER
LOAD
Figure 12. Typical V.11 Interface
-3.25mA
3.25mA
-10V
+10V
-3V
+3V
VZ
IZ
Figure 13. Receiver Input Impedance
相關PDF資料 |
PDF描述 |
|---|---|
| MS3451L12S-3SX | CONN RCPT 2POS CBL MNT W/SCKT |
| GTC020R-28-7P | CONN RCPT 2POS BOX MNT W/PINS |
| MS3451L12S-3SW | CONN RCPT 2POS CBL MNT W/SCKT |
| MS3451L12S-3S | CONN RCPT 2POS CBL MNT W/SCKT |
| MAX233AEWP | IC TXRX DUAL RS232 5V 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MXL1543BCAI-TG05 | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MXL1543CAI | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MXL1543CAI+ | 功能描述:接口 - 專用 5V Multiptcl 3Tx/3Rx Clock/Data Tcvr RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MXL1543CAI+T | 功能描述:接口 - 專用 5V Multiptcl 3Tx/3Rx Clock/Data Tcvr RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MXL1543CAI-T | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。