- 您現在的位置：買賣IC網 > PDF目錄376224 > MXR7202G (Electronic Theatre Controls, Inc.) Low Cost, Low Noise 【2 g Dual Axis Accelerometer with Ratiometric Analog Outputs PDF資料下載
參數資料
| 型號： | MXR7202G |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Low Cost, Low Noise 【2 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| 中文描述： | 低成本，低噪聲【2克雙軸加速度計成比例模擬輸出 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 142K |
| 代理商： | MXR7202G |
EXTERNAL FILTERS
AC Coupling
: For applications where only dynamic
accelerations (vibration) are to be measured, it is
recommended to ac couple the accelerometer output as
shown in Figure 2. The advantage of ac coupling is that
zero
g
offset variations from part to part and zero
g
offset
change over temperature can be eliminated. Figure 3 is a
HFP (high pass filter) with a –3dB breakpoint given by the
equation:
RC
π
2
desirable to have the HFP –3dB point at a very low
frequency in order to detect very low frequency
accelerations. Sometimes the implementation of this HFP
may result in unreasonably large capacitors, and the
designer may turn to digital implementations of HFPs
where very low frequency –3dB breakpoints can be
achieved.
MEMSIC MXR7202G/M Rev.B
Page 5 of 8
3/24/2005
f
1
=
. In many applications it may be
A
OUTX
R
C
A
OUTY
R
C
A
OUTX
Filtered
Output
A
OUTY
Filtered
Output
Figure 2: High Pass Filter
Low Pass Filter
: An external low pass filter would be
useful in low frequency applications such as tilt or
inclination. The low pass filter limits the noise floor and
improves the resolution of the accelerometer
.
The low pass
filter shown in Figure 4 has a –3dB breakpoint given by the
equation:
RC
π
2
device filter, C=0.1
μ
F and R=8k
,
±
5%, 1/8W.
f
1
=
. For the 200 Hz ratiometric output
A
OUTX
R
C
A
OUTY
R
C
A
OUTX
Filtered
Output
A
OUTY
Filtered
Output
Figure 3: Low Pass Filter
POWER SUPPLY NOISE REJECTION
One capacitor is recommended for best rejection of power
supply noise (reference Figure 4 below). The capacitor
should be located as close as possible to the device supply
pin (V
DD
). The capacitor lead length should be as short as
possible, and surface mount capacitor is preferred. For
typical applications, the capacitor can be ceramic 0.1 μF.
Figure 4: Power Supply Noise Rejection
PCB LAYOUT AND FABRICATION SUGGESTIONS
1. Liberal use of ceramic bypass capacitors is
recommended. It is best to solder a 0.1uF capacitor
directly across V
DD
and COM pin.
2. Robust low inductance ground wiring should be used.
3. Care should be taken to ensure there is “thermal
symmetry” on the PCB immediately surrounding the
MEMSIC device and that there is no significant heat
source nearby.
4. A metal ground plane should be added directly beneath
the MEMSIC device. The size of the plane should be
similar to the MEMSIC device’s footprint and be as
thick as possible.
5. Vias can be added symmetrically around the ground
plane. Vias increase thermal isolation of the device
from the rest of the PCB.
相關PDF資料 |
PDF描述 |
|---|---|
| MXR7202M | Low Cost, Low Noise 【2 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| MXR7210G | Low Cost, Low Noise 【10 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| MXR7210M | Low Cost, Low Noise 【10 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| MXR9500G | Low Cost 【1.5 g Tri Axis Accelerometer with Ratiometric Outputs |
| MXR9500M | Low Cost 【1.5 g Tri Axis Accelerometer with Ratiometric Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MXR7202M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost, Low Noise 【2 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| MXR7202ML | 制造商:MEMSIC INC 功能描述:DIGITAL PWM 制造商:MEMSIC 功能描述:ACCELEROMETER 2 AXIS ?G LCC8 |
| MXR7210G | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost, Low Noise 【10 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| MXR7210M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost, Low Noise 【10 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| MXR7210ML | 制造商:MEMSIC 功能描述:ACCELEROMETER 2 AXIS ?0G LCC8 制造商:MEMSIC 功能描述:ACCELEROMETER, 2 AXIS, 10G, LCC8 |
發布緊急采購，3分鐘左右您將得到回復。