- 您現在的位置：買賣IC網 > PDF目錄376224 > MXR7202M (Electronic Theatre Controls, Inc.) Low Cost, Low Noise 【2 g Dual Axis Accelerometer with Ratiometric Analog Outputs PDF資料下載
參數資料
| 型號： | MXR7202M |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Low Cost, Low Noise 【2 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| 中文描述： | 低成本，低噪聲【2克雙軸加速度計成比例模擬輸出 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 142K |
| 代理商： | MXR7202M |
MXR7202G/M PIN DESCRIPTIONS
V
DD
– This is the supply input for the circuits and the
sensor heater in the
accelerometer
. The DC voltage should
be between 2.7 and 5.25 volts. Refer to the section on PCB
layout and fabrication suggestions for guidance on external
parts and connections recommended.
COM
– This is the ground pin for the
accelerometer
.
TP
- This pin should be connected to the ground.
Xout
– This pin is the output of the x-axis acceleration
sensor. The user should ensure the load impedance is
sufficiently high as to not source/sink >100
μ
A typical.
While the sensitivity of this axis has been programmed at
the factory to be the same as the sensitivity for the y-axis,
the
accelerometer
can be programmed for non-equal
sensitivities on the x- and y-axes. Contact the factory for
additional information.
Yout
–
This pin is the output of the y-axis acceleration
sensor. The user should ensure the load impedance is
sufficiently high as to not source/sink >100
μ
A typical.
MEMSIC MXR7202G/M Rev.B
Page 4 of 8
3/24/2005
While the sensitivity of this axis has been programmed at
the factory to be the same as the sensitivity for the x-axis,
the
accelerometer
can be programmed for non-equal
sensitivities on the x- and y-axes. Contact the factory for
additional information.
DISCUSSION OF TILT APPLICATIONS AND
RESOLUTION
Tilt Applications:
One of the most popular applications of
the MEMSIC accelerometer product line is in
tilt/inclination measurement. An accelerometer uses the
force of gravity as an input to determine the inclination
angle of an object.
A MEMSIC accelerometer is most sensitive to changes in
position, or tilt, when the accelerometer’s sensitive axis is
perpendicular to the force of gravity, or parallel to the
Earth’s surface. Similarly, when the accelerometer’s axis is
parallel to the force of gravity (perpendicular to the Earth’s
surface), it is least sensitive to changes in tilt.
Table 1 and Figure 1 help illustrate the output changes in
the X- and Y-axes as the unit is tilted from +90
°
to 0
°
.
Notice that when one axis has a small change in output per
degree of tilt (in m
g
), the second axis has a large change in
output per degree of tilt. The complementary nature of
these two signals permits low cost accurate tilt sensing to
be achieved with the MEMSIC device (reference
application note AN-00MX-007).
M
Figure 1: Accelerometer Position Relative to Gravity
X-Axis
X-Axis
Orientation
To Earth’s
Surface
(deg.)
90
-1.000
85
-0.996
80
-0.985
70
-0.940
60
-0.866
45
-0.707
30
-0.500
20
-0.342
10
-0.174
5
-0.087
0
0.000
Table 1: Changes in Tilt for X- and Y-Axes
Resolution
: The accelerometer resolution is limited by
noise. The output noise will vary with the measurement
bandwidth. With the reduction of the bandwidth, by
applying an external low pass filter, the output noise drops.
Reduction of bandwidth will improve the signal to noise
ratio and the resolution. The output noise scales directly
with the square root of the measurement bandwidth. The
maximum amplitude of the noise, its peak- to- peak value,
approximately defines the worst case resolution of the
measurement. With a simple RC low pass filter, the rms
noise is calculated as follows:
Noise (mg rms) = Noise(mg/
Hz
) *
The peak-to-peak noise is approximately equal to 6.6 times
the rms value (for an average uncertainty of 0.1%).
USING THE MXR7202G/M WITH OPERATING
VOLTAGES OTHER THAN 5V
The MXR7202G/M is tested and specified at V
DD
=5V;
however, it can be powered with V
DD
as low as 2.7V or as
high as 5.25V. Some performance parameters will change
as the supply voltage is varied. The MXR7202G/M output
sensitivity will be linearly proportional to supply voltage.
At 3V the output sensitivity is 3.0/5.0* 312mV/g = 187.2
mV/g. The zero g bias output is also ratiometric, so the zero
g is normally equal to V
DD
/2 at all supply voltages.
Y-Axis
X Output
(
g
)
Change
per deg.
of tilt
(m
g
)
0.15
1.37
2.88
5.86
8.59
12.23
15.04
16.35
17.16
17.37
17.45
Y Output
(
g
)
Change
per deg.
of tilt
(m
g
)
17.45
17.37
17.16
16.35
15.04
12.23
8.59
5.86
2.88
1.37
0.15
0.000
0.087
0.174
0.342
0.500
0.707
0.866
0.940
0.985
0.996
1.000
)
*
)
(
(
Hz
Bandwidth
相關PDF資料 |
PDF描述 |
|---|---|
| MXR7210G | Low Cost, Low Noise 【10 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| MXR7210M | Low Cost, Low Noise 【10 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| MXR9500G | Low Cost 【1.5 g Tri Axis Accelerometer with Ratiometric Outputs |
| MXR9500M | Low Cost 【1.5 g Tri Axis Accelerometer with Ratiometric Outputs |
| MZPS2005610A | Miniature Relays Series M Type MZ 2 poles 10A Monostable |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MXR7202ML | 制造商:MEMSIC INC 功能描述:DIGITAL PWM 制造商:MEMSIC 功能描述:ACCELEROMETER 2 AXIS ?G LCC8 |
| MXR7210G | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost, Low Noise 【10 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| MXR7210M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost, Low Noise 【10 g Dual Axis Accelerometer with Ratiometric Analog Outputs |
| MXR7210ML | 制造商:MEMSIC 功能描述:ACCELEROMETER 2 AXIS ?0G LCC8 制造商:MEMSIC 功能描述:ACCELEROMETER, 2 AXIS, 10G, LCC8 |
| MXR7250VW | 功能描述:Accelerometer X, Y Axis ±5g 27Hz 8-LCC 制造商:memsic inc. 系列:- 包裝:剪切帶（CT） 零件狀態:停產 類型:模擬 軸:X，Y 加速度范圍:±5g 靈敏度（LSB/g）:- 靈敏度（mV/g）:250 帶寬:27Hz 輸出類型:模擬電壓 電壓 - 電源:4.5 V ~ 5.25 V 特性:- 工作溫度:-40°C ~ 95°C（TA） 安裝類型:表面貼裝 封裝/外殼:8-LCC 供應商器件封裝:8-LCC 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。