- 您現在的位置：買賣IC網 > PDF目錄361089 > NCN6000 (ON SEMICONDUCTOR) Compact Smart Card Interface IC(智能卡接口集成電路) PDF資料下載
參數資料
| 型號： | NCN6000 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Compact Smart Card Interface IC(智能卡接口集成電路) |
| 中文描述： | 緊湊型智能卡接口IC（智能卡接口集成電路） |
| 文件頁數： | 17/36頁 |
| 文件大小： | 358K |
| 代理商： | NCN6000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
NCN6000
http://onsemi.com
17
Transaction Mode
During the transaction mode, the NCN6000 maintains
power supply and clock signal to the card. All the signal
levels related with the card are translated as necessary to
cope with the MPU and the card.
The DCDC converter status and the Vbat state can be
monitored on the STATUS by using the A0 and A1 logic
inputs as depicted in Tables 3 and 4.
Transaction Mode
Logic Conditions:
Card Output:
CS
PWR_ON = H
A0
A1
PGM
I/O
= L
= H
= H
= H
= DATA
TRANSFER
= H/L
= L/H DCDC
status: Fail/Pass
RESET
STATUS
CRD_VCC = 3.0 or 5.0 V
CRD_CLK = CLOCK
CRD_RST = H/L
CRD_IO
= DATA
TRANSFER
To make sure the data are not polluted by power losses, it
is recommended to check the state of CRD_VCC before
launching a new data transaction. Since CS = L, this is
achieved by forcing bits A0 and A1 according to Table 4, and
reading the STATUS pin 5.
Idle Mode
The idle mode is used when a card is powered up
(CRD_VCC = Vcc), without communication on going.
Idle Mode
Logic Conditions:
Card Output:
CS
PWR_ON = H
A0
A1
PGM
I/O
RESET
STATUS
= L
= H
= H
= H
= Z
= H
= L/H according
to the internal
register results
CRD_VCC = 3.0 or 5.0 V
CRD_CLK = CLOCK active or
L or H
CRD_RST = H
CRD_IO
= Z
In addition, the CRD_CLK signal can be stopped, as
depicted in Tables 3 and 4, to minimize the current
consumption of the external smart card, leaving CRD_VCC
active.
Power Down Operation
The power down mode can be initiated by either the
external MPU (pulling PWR_ON = L) or by one of the
internal error condition (CRD_VCC overload or Vbat Low).
The communication session is terminated immediately,
according to the ISO78163 sequence. On the other hand,
the MPU can run the Standby mode by forced CS = H.
When the card is extracted, the interface shall detect the
operation and run the Power Shut Off of the card as
described by the ISO/CEI 78163 sequence depicted here
after:
ISO78163 sequence:
Force RST to Low
Force CLK to Low, unless it is already in this state
Force CRD_IO to Low
Shut Off the CRD_VCC supply
Since the internal digital filter is activated for any card
insertion or extraction, the physical power sequence will be
activated 150 s maximum after the card has been extracted.
Of course, such a delay does not exist when the MPU launch
the power down intentionally.
The time delay between each negative going signal is
500 ns typical (Figure 10).
相關PDF資料 |
PDF描述 |
|---|---|
| NCN6001DTBR2 | Compact Smart Card Interface IC |
| NCN6001 | Compact Smart Card Interface IC |
| NCN6004AFTBR2 | Dual SAM/SIM Interface Integrated Circuit |
| NCN6004A | Dual SAM/SIM Interface Integrated Circuit |
| NCN6010DTBR2 | SIM Card Supply and Level Shifter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN6000/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Compact Smart Card Interface IC |
| NCN6000DTB | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6000DTBG | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6000DTBR2 | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6000DTBR2G | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。