- 您現在的位置：買賣IC網 > Datasheet目錄45 > NCP1083DEG (ON Semiconductor)IC CONV CTLR POE-PD 40W 20-TSSOP Datasheet資料下載
參數資料
| 型號： | NCP1083DEG |
| 廠商： | ON Semiconductor |
| 文件頁數： | 12/18頁 |
| 文件大小： | 257K |
| 描述： | IC CONV CTLR POE-PD 40W 20-TSSOP |
| 標準包裝： | 74 |
| 類型： | 以太網供電開關（PoE） |
| 應用： | 遠程外設（工業(yè)控制，相機，數據訪問） |
| 內部開關： | 是 |
| 電流限制： | 1.1A |
| 電源電壓： | 0 V ~ 57 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬）裸露焊盤 |
| 供應商設備封裝： | 20-TSSOP-EP |
| 包裝： | 管件 |
NCP1083
http://onsemi.com
12
1st Class Event
Class range
Mark Range
Reset Range
2 Fingers Classification
0 V
5.4 V
9.7 V
13 V
20.5 V
UVLO_on
Power On
Detection
PSE identified as type 2 PSE (at)
PSE identified by default as type 1 PSE (af)
PSE Type identification:
Number of Mark Event:
0
1
2
X
Operation Mode:
Figure 9. Hardware Physical Classification Event Sequence
with Mark Events (.at spec)
1st Mark Event 2nd Class Event 2nd Mark Event
nCLASS_AT Indicator
The nCLASS_AT active low open drain output pin can be
used to notify to the microprocessor of the powered device
that the PSE performed a one or two event hardware
classification. If a two event hardware classification has
occured and once the PD application is supplied power by
the NCP1083 DC-DC converter, the nCLASS_AT pin will
be pulled down to ARTN by the internal low voltage NMOS
switch (ARTN is the ground connection of the DC-DC
converter). Otherwise, nCLASS_AT will be disabled and
will be pulled up to VDDL (3.3 V typ) via an internal current
source (20 mA typ) and via the external pull-up resistor.
The following scheme illustrates how the nCLASS_AT
pin may be configured with the processor of the powered
device. An opto-coupler is used to guarantee full isolation
between the Ethernet cable and the application.
Figure 10. Isolated nClass_AT Communication with the Powered Device Application
As soon as the application is powered by the DC-DC
converter and completes initialization, the microprocessor
should check if the NCP1083 detected a two event hardware
classification by reading its digital input (pin IN1 in this
example). If pin IN1 is low, the application knows power is
supplied by a IEEE 802.3at compliant PSE, and can deliver
power up to the level specified by the IEEE 802.3at standard.
Otherwise the application will have to perform a Layer 2
classification with the PSE. There are several scenarios for
which the NCP1083 will not enable its nCLASS_AT pin:
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1501DMR2G | IC REG SGL BUCK/LINEAR 8MICRO |
| NCP1578MNR2G | IC REG DL BCK/LINEAR SYNC 20-QFN |
| NCP1601BDR2G | IC PFC CTRL CRM/TRANSITION 8SOIC |
| NCP1603D100R2G | IC CTLR PFC/PWM COMBO 16-SOIC |
| NCP1605DR2G | IC PFC CONTROLLER CCM/DCM 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1083DER2G | 功能描述:DC/DC 開關控制器 POE-PD 40W DC-DC AUX SUPP RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| NCP1083QBCGEVB | 功能描述:電源管理IC開發(fā)工具 HIGH POWER POE-PD MODULE RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1083WIRGEVB | 功能描述:電源管理IC開發(fā)工具 POE-PD MODULE WITH VAUX RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1086 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator |
| NCP1086/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator |
發(fā)布緊急采購，3分鐘左右您將得到回復。