- 您現在的位置：買賣IC網 > PDF目錄5342 > NCS7101SN1T1 (ON Semiconductor)IC OPAMP SGL R-R 1.8V 5TSOP PDF資料下載
參數資料
| 型號： | NCS7101SN1T1 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP SGL R-R 1.8V 5TSOP |
| 產品變化通告： | Product Obsolescence 11/Feb/2009 |
| 標準包裝： | 3,000 |
| 放大器類型： | 通用 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 1.2 V/µs |
| 增益帶寬積： | 1MHz |
| 電流 - 輸入偏壓： | 1pA |
| 電壓 - 輸入偏移： | 600µV |
| 電流 - 電源： | 1.13mA |
| 電流 - 輸出 / 通道： | 72mA |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 10 V，±0.9 V ~ 5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-TSOP（0.059"，1.50mm 寬）5 引線 |
| 供應商設備封裝： | 5-TSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | NCS7101SN1T1OS |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
NCS7101, NCV7101
http://onsemi.com
10
APPLICATION INFORMATION AND OPERATING DESCRIPTION
GENERAL INFORMATION
The NCS7101 is a railtorail input, railtorail output
operational amplifier that features guaranteed 1.8 volt
operation. This feature is achieved with the use of a modified
analog CMOS process that allows the implementation of
depletion MOSFET devices. The amplifier has a 1.0 MHz
gain bandwidth product, 1.2 V/
ms slew rate and is
operational over a power supply range less than 1.8 V to as
high as 10 V.
Inputs
The input topology of this device series is unconventional
when compared to most low voltage operational amplifiers.
It consists of an Nchannel depletion mode differential
transistor pair that drives a folded cascode stage and current
mirror. This configuration extends the input common mode
voltage range to encompass the VEE and VCC power supply
rails, even when powered from a combined total of less than
1.8 volts. Figures 27 and 28 show the input common mode
voltage range versus power supply voltage.
The differential input stage is laser trimmed in order to
minimize offset voltage. The Nchannel depletion mode
MOSFET input stage exhibits an extremely low input bias
current of less than 40 pA. The input bias current versus
temperature is shown in Figure 4. Either one or both inputs
can be biased as low as VEE minus 300 mV to as high as 10 V
without causing damage to the device. If the input common
mode voltage range is exceeded, the output will not display
a phase reversal but it may latch in the appropriate high or
low state. The device can then be reset by removing and
reapplying power. If the maximum input positive or
negative voltage ratings are to be exceeded, a series resistor
must be used to limit the input current to less than 2.0 mA.
The ultra low input bias current of the NCS7101 allows
the use of extremely high value source and feedback resistor
without reducing the amplifier’s gain accuracy. These high
value resistors, in conjunction with the device input and
printed circuit board parasitic capacitances Cin, will add an
additional pole to the single pole amplifier shown in
Figure 30. If low enough in frequency, this additional pole
can reduce the phase margin and significantly increase the
output settling time. The effects of Cin, can be canceled by
placing a zero into the feedback loop. This is accomplished
with the addition of capacitor Cfb. An approximate value for
Cfb can be calculated by:
Cfb +
Rin
Cin
Rfb
Figure 30. Input Capacitance Pole Cancellation
+
-
Output
Rfb
Cin
Rin
Cfb
Cin = Input and printed circuit board capacitance
Input
Output
The output stage consists of complementary P and N
channel devices connected to provide railtorail output
drive. With a 2.0 k load, the output can swing within 100 mV
of either rail. It is also capable of supplying over 95 mA
when powered from 10 V and 3.0 mA when powered from
1.8 V.
When connected as a unity gain follower, the NCS7101
can directly drive capacitive loads in excess of 390 pF at
room temperature without oscillating but with significantly
reduced phase margin. The unity gain follower
configuration exhibits the highest bandwidth and is most
prone to oscillations when driving a high value capacitive
load. The capacitive load in combination with the
amplifier’s output impedance, creates a phase lag that can
result in an underdamped pulse response or a continuous
oscillation. Figure 32 shows the effect of driving a large
capacitive load in a voltage follower type of setup. When
driving capacitive loads exceeding 390 pF, it is
recommended to place a low value isolation resistor
between the output of the op amp and the load, as shown in
Figure 31. The series resistor isolates the capacitive load
from the output and enhances the phase margin. Refer to
Figure 33. Larger values of R will result in a cleaner output
waveform but excessively large values will degrade the
large signal rise and fall time and reduce the output’s
amplitude. Depending upon the capacitor characteristics,
the isolation resistor value will typically be between 50 to
500 ohms. The output drive capability for resistive and
Figure 31. Capacitance Load Isolation
+
-
Output
R
Isolation resistor R = 50 to 500
CL
Input
Note that the lowest phase margin is observed at cold
temperature and low supply voltage.
相關PDF資料 |
PDF描述 |
|---|---|
| 953224-2000-AR-PR | CONN SOCKET 24POS 2MM VERT SMD |
| IXBOD1-08 | IC SGL DIODE BOD 0.9A 800V FP |
| LT1097CN8 | IC PREC OP-AMP LOW-COST/PWR 8DIP |
| 7100.1021.13 | FUSE 4A 250V T-LAG 3.5MM PCB |
| NCP4300ADR2 | IC OPAMP/VOLT REF DUAL 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCS7101SN1T1G | 功能描述:運算放大器 - 運放 1.8-10V Sngl Rail to Rail Industrial Temp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| NCS7101SN2T1 | 功能描述:運算放大器 - 運放 1.8-10V Sngl Rail to RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| NCS7101SN2T1G | 功能描述:運算放大器 - 運放 1.8-10V Sngl Rail to Rail Industrial Temp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| NCS7301SN1T1G | 功能描述:運算放大器 - 運放 RoHS:否 制造商:ON Semiconductor 通道數量: 共模抑制比（最小值）: 輸入補償電壓: 輸入偏流（最大值）: 工作電源電壓: 安裝風格: 封裝 / 箱體: 轉換速度: 關閉: 輸出電流: 最大工作溫度: 封裝: |
| NCS8353 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Stereo 20W/Ch Class D Audio Power Amplifier with Programmable Power Limit and Selectable Gain |
發布緊急采購，3分鐘左右您將得到回復。