- 您現在的位置：買賣IC網 > PDF目錄224600 > NKE0509DC (MURATA POWER SOLUTIONS INC) 1-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | NKE0509DC |
| 廠商： | MURATA POWER SOLUTIONS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, DIP-8/4 |
| 文件頁數： | 2/4頁 |
| 文件大?。?/td> | 144K |
| 代理商： | NKE0509DC |
KDC_NKEC.J01 Page 2 of 4
Technical enquiries - email: mk@murata-ps.com, tel: +44 (0)1908 615232
www.murata-ps.com
NKE Series
Isolated Sub-Miniature 1W Single Output DC/DC Converters
OUTPUT CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Max.
Units
Rated Power
TA=-40°C to 120°C, see derating graphs
1.0
W
Voltage Set Point Accuracy
See tolerance envelope
Line regulation
High VIN to low VIN
1.0
1.2
%/%
Load Regulation1
10% load to rated load, 3.3V output types & 0309
10
15
%
10% load to rated load, 5V output types
12
15
10% load to rated load, 9V output types
7.5
10
10% load to rated load, 12V output types
6.5
9.5
10% load to rated load, 15V output types
6.0
8.5
Ripple and Noise
BW=DC to 20MHz, 3.3V output types & 0305, 0505SEC, 0505DEC
40
80
mV p-p
BW=DC to 20MHz, other 5V output types
77
100
BW=DC to 20MHz, 9V output types
43
90
BW=DC to 20MHz, 12V output types
35
65
BW=DC to 20MHz, 15V output types
32
55
ISOLATION CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Max.
Units
Isolation test voltage
Flash tested for 1 second
3000
VDC
Resistance
Viso= 1000VDC
10
GΩ
GENERAL CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Max.
Units
Switching frequency
All output types
115
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Max.
Units
Specication
All output types
-40
85
°C
Storage
-50
130
Case temperature rise above
ambient
0505D/S, 1205D/S
41
All other output types
32
Cooling
Free air convection
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a specied time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NKE series of dc/dc converters are all 100% production tested at their stated isolation voltage. This is 1000V DC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
The NKE series has been recognized by Underwriters Laboratory for functional insulation. Both input and output should normally be maintained within SELV limits i.e. less than
42.4V peak, or 60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation sys-
tem. The part could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the
barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry
according to safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materi-
als, construction and environment. While manufactured parts can withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any
material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of
tests should be strictly limited. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from
specied test voltage.
1. 12V input types have typically 3% less load regulation.
SAFETY APPROVAL
The NKE series has been recognised by Underwriters Laboratory (UL) to UL 60950 for functional insulation in a maximum ambient temperature of 85C and/or case temperature
limit of 130C. Case temperature measured on the face opposite the pins. File number E179522 applies.
相關PDF資料 |
PDF描述 |
|---|---|
| NKE1212D | 1-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
| NKS2JAB1-32.0000-20(T) | QUARTZ CRYSTAL RESONATOR, 32 MHz |
| NKS2JAB1-40.0000-20 | QUARTZ CRYSTAL RESONATOR, 40 MHz |
| NKS2HAA1-38.4000-12(T) | QUARTZ CRYSTAL RESONATOR, 38.4 MHz |
| NKS2HAA1-48.0000-20(T) | QUARTZ CRYSTAL RESONATOR, 48 MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NKE0509S | 功能描述:DC/DC轉換器 USE 580-NKE0509SC RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| NKE0509S | 制造商:Murata Power Solutions 功能描述:DC/DC CONVERTER SIL 1W 9V |
| NKE0509SC | 功能描述:DC/DC轉換器 1W Single Output 5V to 9V 111mA RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| NKE0509XDC | 制造商:MICRODC 制造商全稱:MICRODC 功能描述:Isolated Sub-Miniature 1W Single Output DC/DC Converters |
| NKE0509XSC | 制造商:MICRODC 制造商全稱:MICRODC 功能描述:Isolated Sub-Miniature 1W Single Output DC/DC Converters |
發布緊急采購，3分鐘左右您將得到回復。