- 您現在的位置：買賣IC網 > PDF目錄378029 > OP181GP (ANALOG DEVICES INC) Ultralow Power, Rail-to-Rail Output Operational Amplifiers PDF資料下載
參數資料
| 型號： | OP181GP |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Ultralow Power, Rail-to-Rail Output Operational Amplifiers |
| 中文描述： | OP-AMP, 2500 uV OFFSET-MAX, 0.105 MHz BAND WIDTH, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 448K |
| 代理商： | OP181GP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁
OP181/OP281/OP481
–11–
REV. 0
10
0%
100
90
0.2ms
0.1V
0V
V
IN
V
OUT
Figure 35. Input and Output Signals with V
CM
< 0 V
Overdrive Recovery Time
The amount of time it takes for an amplifier to recover from
saturation can be an important consideration when using an
amplifier as a comparator or when outputs can be driven to the
supplies. The overdrive recovery time for the OP181 is 50
μ
s
with the amplifier running from a 3 volt supply and increases
to 100
μ
s with a 10 volt supply. Figure 36 shows the result of
the OP181 running from a 3 V supply with its output being
overdriven.
10
0%
100
90
0.2ms
0.1V
V
S
= +3V
A
V
= +100
V
IN
SCALE 0.1V
0V
V
SCALE 1V
0V
Figure 36. Output of the Op Amp Recovering from
Saturation
Capacitive Loading
Most low supply current amplifiers have difficulty driving
capacitive loads due to the higher currents required from the
output stage for such loads. Higher capacitance at the output
will increase the amount of overshoot and ringing in the
amplifier’s step response and could even affect the stability of
the device. However, through careful design of the output stage
and its high phase margin, the OPx81 family can tolerate some
degree of capacitive loading. Figure 37 shows the step response
of an OP181 with a 10 nF capacitor connected at the output.
Notice that the overshoot of the output does not exceed more
than 10% with such a load, even with a supply voltage of only
+3 V.
10
0%
100
90
Figure 37. Ringing and Overshoot of the Output of the
Amplifier
A Micropower Reference Voltage Generator
Many single supply circuits are configured with the circuit
biased to 1/2 of the supply voltage. In these cases, a false-
ground reference can be created by using a voltage divider
buffered by an amplifier. Figure 38 shows the schematic for
such a circuit.
The two 1 M
resistors generate the reference voltage while
drawing only 1.5
μ
A of current from a 3 V supply. A capacitor
connected from the inverting terminal to the output of the op
amp provides compensation to allow for a bypass capacitor to be
connected at the reference output. This bypass capacitor helps
establish an ac ground for the reference output. The entire
reference generator draws less than 5
μ
A from a 3 V supply
source.
6
7
4
2
3
OP181
10k
0.022μF
V
+1.5V TO +6V
1μF
1μF
1M
+3V TO +12V
100
1M
Figure 38. A Micropower Bias Voltage Generator
A Window Comparator
The extremely low power supply current demands of the OPx81
family make it ideal for use in long life battery powered applica-
tions such as a monitoring system. Figure 39 shows a circuit
that uses the OP281 as a window comparator.
相關PDF資料 |
PDF描述 |
|---|---|
| OP181GS | Ultralow Power, Rail-to-Rail Output Operational Amplifiers |
| OP181 | Ultralow Power, Rail-to-Rail Output Operational Amplifiers |
| OP186 | 5 uA, Rail-to-Rail Output Operational Amplifier |
| OP186GRT | CONNECTOR ACCESSORY |
| OP193FS-REEL | Precision, Micropower Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OP181GS | 制造商:Rochester Electronics LLC 功能描述:SINGLE 5UA RAIL TO RAIL O - Bulk |
| OP181GS-REEL7 | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| OP183 | 制造商:AD 制造商全稱:Analog Devices 功能描述:5 MHz Single-Supply Operational Amplifier |
| OP183_05 | 制造商:AD 制造商全稱:Analog Devices 功能描述:5 MHz Single-Supply Operational Amplifier |
| OP183GP | 制造商:Rochester Electronics LLC 功能描述:SINGLE SUPPLY 5MHZ OP AMP - Bulk 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。